- 您現在的位置：買賣IC網 > PDF目錄374032 > ADSP-2104LKP-55 (ANALOG DEVICES INC) Low Cost DSP Microcomputers PDF資料下載
參數資料
| 型號： | ADSP-2104LKP-55 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | Low Cost DSP Microcomputers |
| 中文描述： | 24-BIT, 13.824 MHz, OTHER DSP, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 15/36頁 |
| 文件大小： | 333K |
| 代理商： | ADSP-2104LKP-55 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ADSP-2104/ADSP-2109
REV. 0
–15–
T E ST CONDIT IONS
Figure 10 shows voltage reference levels for ac measurements.
3.0V
1.5V
0.0V
2.0V
1.5V
0.8V
INPUT
OUTPUT
Figure 10. Voltage Reference Levels for AC Measurements
(Except Output Enable/Disable)
Output Disable T ime
Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured
output high or low voltage to a high impedance state. T he
output disable time (t
DIS
) is the difference of t
MEASURED
and
t
DECAY
, as shown in Figure 11. T he time t
MEASURED
is the
interval from when a reference signal reaches a high or low
voltage level to when the output voltages have changed by 0.5 V
from the measured output high or low voltage.
T he decay time, t
DECAY
, is dependent on the capacitative load,
C
L
, and the current load, i
L
, on the output pin. It can be
approximated by the following equation:
t
DECAY
=
C
L
×
0.5
V
i
L
from which
t
DIS
=
t
MEASURED
–
t
DECAY
is calculated. If multiple pins (such as the data bus) are dis-
abled, the measurement value is that of the last pin to stop
driving.
Output E nable T ime
Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start
driving. T he output enable time (t
E NA
) is the interval from
when a reference signal reaches a high or low voltage level to
when the output has reached a specified high or low trip point,
as shown in Figure 11. If multiple pins (such as the data bus)
are enabled, the measurement value is that of the first pin to
start driving.
SPECIFICATIONS (ADSP-2104/ADSP-2109)
Figure 12. Equivalent Device Loading for AC Measurements
(Except Output Enable/Disable)
2.0V
1.0V
t
ENA
REFERENCE
SIGNAL
OUTPUT
t
DECAY
V
OH
(MEASURED)
OUTPUT STOPS
DRIVING
OUTPUT STARTS
DRIVING
t
DIS
t
MEASURED
V
OL
(MEASURED)
V
OH
(MEASURED) – 0.5V
V
OL
(MEASURED) +0.5V
HIGH-IMPEDANCE STATE.
TEST CONDITIONS CAUSE
THIS VOLTAGE LEVEL TO BE
APPROXIMATELY 1.5V.
V
OH
(MEASURED)
V
OL
(MEASURED)
Figure 11. Output Enable/Disable
TO
OUTPUT
PIN
50pF
+1.5V
I
OH
I
OL
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21160M | DSP Microcomputer |
| ADSP-21160MKB-80 | DSP Microcomputer |
| ADSP-21160NKB-95 | DSP Microcomputer |
| ADSP-21160N | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| ADSP-21160NCB-TBD | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP2105 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:(666.40 k) |
| ADSP-2105 | 制造商:AD 制造商全稱:Analog Devices 功能描述:ADSP-2100 Family DSP Microcomputers |
| ADSP-2105BP-55 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 13.824MHz 13.824MIPS 68-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ADSP-2105BP-55REEL | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| ADSP-2105BP-80 | 功能描述:IC DSP CONTROLLER 16BIT 68PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。