欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADSP-2196MKCA-160X
廠商: ANALOG DEVICES INC
元件分類: 數字信號處理
英文描述: DSP Microcomputer
中文描述: 16-BIT, 160 MHz, OTHER DSP, PBGA144
封裝: MINI, BGA-144
文件頁數: 14/68頁
文件大小: 897K
代理商: ADSP-2196MKCA-160X
For current information contact Analog Devices at 800/262-5643
ADSP-2196
Clear (= 0) the PDWN bit in the PLLCTL register
Set (= 1) the STOPALL bit in the PLLCTL register
To exit Power-Down Core/Peripherals mode, the DSP
responds to an interrupt and (after five to six cycles of
latency) resumes executing instructions with the instruction
after the IDLE.
September 2001
This information applies to a product under development. Its characteristics and specifications are subject to change with-
out notice. Analog Devices assumes no obligation regarding future manufacturing unless otherwise agreed to in writing.
14
REV. PrA
Power-Down All Mode
When the ADSP-2196 is in Power-Down All mode, the
DSP core clock, the peripheral clock, and the PLL are all
stopped. The DSP does not retain the contents of the
instruction pipeline. The peripheral bus is stopped, so the
peripherals cannot receive data.
To enter Power-Down All mode, the DSP executes an IDLE
instruction after performing the following tasks:
Enter a power-down interrupt service routine
Check for pending interrupts and I/O service routines
Set (= 1) the PDWN bit in the PLLCTL register
To exit Power-Down Core/Peripherals mode, the DSP
responds to an interrupt and (after 500 cycles to re-stabilize
the PLL) resumes executing instructions with the instruc-
tion after the IDLE.
Clock Signals
The ADSP-2196 can be clocked by a crystal oscillator or a
buffered, shaped clock derived from an external clock oscil-
lator. If a crystal oscillator is used, the crystal should be
connected across the CLKIN and XTAL pins, with two
capacitors connected as shown in
Figure 6
. Capacitor
values are dependent on crystal type and should be specified
by the crystal manufacturer. A parallel-resonant, funda-
mental frequency, microprocessor-grade crystal should be
used for this configuration.
If a buffered, shaped clock is used, this external clock
connects to the DSP’s CLKIN pin. CLKIN input cannot
be halted, changed, or operated below the specified
frequency during normal operation. This clock signal
should be a TTL-compatible signal. When an external clock
is used, the XTAL input must be left unconnected.
The DSP provides a user-programmable 1 to 32 multi-
plication of the input clock, including some fractional
values, to support 128 external to internal (DSP core) clock
ratios. The MSEL6–0, BYPASS, and DF pins decide the
PLL multiplication factor at reset. At runtime, the multipli-
cation factor can be controlled in software. To support input
clocks greater that 100 MHz, the PLL uses an additional
input: the Divide Frequency (DF) pin. If the input clock is
greater than 100 MHz, DF must be high. If the input clock
is less than 100 MHz, DF must be low. The combination of
pullup and pull-down resistors in
Figure 6
set up a core
clock ratio of 6:1, which produces a 150 MHz core clock
from the 25 MHz input. For other clock multiplier settings,
see the
ADSP-219x/2191 DSP Hardware Reference
.
The peripheral clock is supplied to the CLKOUT pin.
All on-chip peripherals for the ADSP-2196 operate at the
rate set by the peripheral clock. The peripheral clock is
either equal to the core clock rate or one-half the DSP core
clock rate. This selection is controlled by the IOSEL bit in
the PLLCTL register. The maximum core clock
is 160 MHz, and the maximum peripheral clock
is 100 MHz—the combination of the input clock and
core/peripheral clock ratios may not exceed these limits.
Reset
The RESET signal initiates a master reset of the
ADSP-2196. The RESET signal must be asserted during
the power-up sequence to assure proper initialization.
RESET during initial power-up must be held long enough
to allow the internal clock to stabilize. If RESET is activated
any time after power up, the clock does not continue to run
and requires stabilization time when recovering from reset.
The power-up sequence is defined as the total time required
for the crystal oscillator circuit to stabilize after a valid V
DD
is applied to the processor, and for the internal phase-locked
loop (PLL) to lock onto the specific crystal frequency. A
minimum of 100 μs ensures that the PLL has locked, but
does not include the crystal oscillator start-up time. During
Figure 6. External Crystal Connections
&
&
!
"
))
''
)0
+
(
(
%
--
&.
-
1 ) 0
&
)'0 &.
相關PDF資料
PDF描述
ADSP-2196MKST-160X DSP Microcomputer
ADSP-21990 16-bit fixed point DSP with Flash
ADSP-21990BBC 16-bit fixed point DSP with Flash
ADSP-21990BST 16-bit fixed point DSP with Flash
ADSP-21MOD870-100 Single Chip Digital Modem(單片數字調制解調器)
相關代理商/技術參數
參數描述
ADSP-2196MKST-160 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 144-Pin LQFP 制造商:Analog Devices 功能描述:16-Bit DSP 160 MIPs 2.5V 40 Kbytes
ADSP-2196MKSTZ-160 功能描述:IC DSP CONTROLLER 16BIT 144-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C,McASP,McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA,FCBGA 供應商設備封裝:548-FCBGA(27x27) 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA
ADSP-21990BBC 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA 制造商:Rochester Electronics LLC 功能描述:160 MIPS, MIXED SIGNAL DSPWITH 14-BIT - Bulk
ADSP-21990BST 制造商:Rochester Electronics LLC 功能描述:160 MIPS,MIXED SIGNAL DSP WITH 14BIT - Tape and Reel
ADSP-21990BSTZ 功能描述:IC DSP CONTROLLER 16BIT 176-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP(數字式信號處理器) 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI,以太網,RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA,FCBGA 供應商設備封裝:431-FCPBGA(20x20) 包裝:托盤
主站蜘蛛池模板: 祁连县| 甘肃省| 沙坪坝区| 赤壁市| 来安县| 田东县| 九龙城区| 松潘县| 西平县| 和平区| 深泽县| 买车| 镇江市| 新营市| 砚山县| 额敏县| 西藏| 福鼎市| 太保市| 兴隆县| 龙江县| 洪洞县| 宣汉县| 屏南县| 太仆寺旗| 绍兴县| 临洮县| 嫩江县| 宜君县| 大冶市| 达州市| 嘉峪关市| 广平县| 灵寿县| 萝北县| 逊克县| 酉阳| 灌阳县| 浦县| 玉林市| 三河市|