- 您現在的位置：買賣IC網 > PDF目錄374038 > ADT7463 (Analog Devices, Inc.) dB COOL Remote Thermal Controller and Voltage Monitor PDF資料下載
參數資料
| 型號： | ADT7463 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | dB COOL Remote Thermal Controller and Voltage Monitor |
| 中文描述： | 分貝超酷的遠程熱控制器和電壓監視器 |
| 文件頁數： | 6/53頁 |
| 文件大小： | 719K |
| 代理商： | ADT7463 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
REV. 0
–6–
ADT7463
FUNCTIONAL DESCRIPTION
General Description
The ADT7463 is a complete systems monitor and multiple fan
controller for any system requiring monitoring and cooling. The
device communicates with the system via a serial System
Management Bus. The serial bus controller has an optional
address line for device selection (Pin 14), a serial data line
for reading and writing addresses and data (Pin 1), and an input
line for the serial clock (Pin 2). All control and programming
functions of the ADT7463 are performed over the serial bus. In
addition, two of the pins can be reconfigured as an
SMBALERT
output to indicate out-of-limit conditions.
Measurement Inputs
The device has six measurement inputs, four for voltage and
two for temperature. It can also measure its own supply voltage
and can measure ambient temperature with its on-chip tempera-
ture sensor.
Pins 20 through 23 are analog inputs with on-chip attenuators,
configured to monitor 5 V, 12 V, 2.5 V, and the processor core
voltage (2.25 V input), respectively.
Power is supplied to the chip via Pin 4, and the system also
monitors V
CC
through this pin. In PCs, this pin is normally
connected to a 3.3 V standby supply. This pin can, however, be
connected to a 5 V supply and monitor it without overranging.
Remote temperature sensing is provided by the D1 and D2
inputs, to which diode-connected, external temperature-sensing
transistors such as a 2N3904 or CPU thermal diode may be
connected.
The ADC also accepts input from an on-chip band gap tem-
perature sensor that monitors system ambient temperature.
Sequential Measurement
When the ADT7463 monitoring sequence is started, it cycles
sequentially through the measurement of analog inputs and the
temperature sensors. Measured values from these inputs are
stored in Value registers. These can be read out over the serial
bus, or can be compared with programmed limits stored in the
Limit registers. The results of out-of-limit comparisons are
stored in the Status registers, which can be read over the serial
bus to flag out-of-limit conditions.
Processor Voltage ID
Five digital inputs (VID0 to VID5—Pins 5 to 8, 19, and 21)
read the processor Voltage ID code and store it in the VID
register, from which it can be read out by the management
system over the serial bus. The VID code monitoring function is
compatible with both VRM9.x and future VRM10 solutions.
Additionally, an
SMBALERT
can be generated to flag a change
in VID code.
ADT7463 Address Selection
Pin 13 is the dual function PWM3/
ADDRESS ENABLE
pin.
If Pin 13 is pulled low on power-up, the ADT7463 will read the
state of Pin 14 (TACH4/ADDRESS SELECT/
THERM
pin) to
determine the ADT7463’s slave address. If Pin 13 is high on
power-up, then the ADT7463 will default to SMBus slave
address 0x2E. This function is described in more detail later.
INTERNAL REGISTERS OF THE ADT7463
A brief description of the ADT7463’s principal internal registers
is given below. More detailed information on the function of
each register is given in Tables IV to XLII.
Configuration Registers
The Configuration registers provide control and configuration
of the ADT7463, including alternate pinout functionality.
Address Pointer Register
This register contains the address that selects one of the other
internal registers. When writing to the ADT7463, the first byte
of data is always a register address, which is written to the
Address Pointer Register.
Status Registers
These registers provide the status of each limit comparison and
are used to signal out-of-limit conditions on the temperature,
voltage, or fan speed channels. If Pin 10 or Pin 22 is con-
figured as
SMBALERT
, then this pin will assert low whenever
a status bit gets set.
Interrupt Mask Registers
These registers allow each interrupt status event to be masked
when Pin 10 or Pin 22 is configured as an
SMBALERT
output.
VID Register
The status of the VID0 to VID5 pins of the processor can read
from this register. VID code changes can also generate
SMBALERT
interrupts.
Value and Limit Registers
The results of analog voltage inputs, temperature, and fan
speed measurements are stored in these registers, along with
their limit values.
Offset Registers
These registers allow each temperature channel reading to be
offset by a twos complement value written to these registers.
T
MIN
Registers
These registers program the starting temperature for each fan
under Automatic Fan Speed Control.
T
RANGE
Registers
These registers program the temperature-to-fan speed control
slope in Automatic Fan Speed Control Mode for each PWM
output.
Operating Point Registers
These registers define the target operating temperatures for each
thermal zone when running under dynamic T
MIN
control. This
function allows the cooling solution to adjust dynamically in
response to measured temperature and system performance.
Enhance Acoustics Registers
These registers allow each PWM output controlling fan to be
tweaked to enhance the system’s acoustics.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7463ARQ | dB COOL Remote Thermal Controller and Voltage Monitor |
| ADT7466 | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ-REEL | dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ-REEL7 | dBCool Remote Thermal Controller and Voltage Monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7463ARQ | 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7463ARQ-REEL | 功能描述:IC SENSOR TEMP FAN-CTRL 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7463ARQ-REEL7 | 功能描述:IC SENSOR TEMP FAN-CTRL 24QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7463ARQZ | 功能描述:馬達/運動/點火控制器和驅動器 SYS MGMT CNTRLR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADT7463ARQZ-R7 | 功能描述:板上安裝溫度傳感器 SYS MGMT CNTRLR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。