- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7481ARMZ-1RL (ON Semiconductor)IC SENSOR TEMP 2CH ALARM 10MSOP Datasheet資料下載
參數資料
| 型號： | ADT7481ARMZ-1RL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 10/20頁 |
| 文件大小： | 237K |
| 描述： | IC SENSOR TEMP 2CH ALARM 10MSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 120°C，外部傳感器 |
| 精確度： | ±2.5°C（最小值） |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 120°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | ADT7481ARMZ-1REEL ADT7481ARMZ-1REEL-ND |
ADT7481
http://onsemi.com
10
Table 11. CONVERSION RATE/CHANNEL SELECTOR REGISTER (READ ADDRESS 0x04, WRITE ADDRESS 0x0A)
Bit
Mnemonic
Function
7
Averaging
Setting this bit to 1 disables averaging of the temperature measurements at the slower conversion
rates (averaging cannot take place at the three faster rates, so setting this bit has no effect). When
default = 0, averaging is enabled.
6
Reserved
Reserved for future use. Do not write to this bit.
<5:4>
Channel Selector
These bits are used to select the temperature measurement channels:
00 = Round Robin = Default = All Channels Measured
01 = Local Temperature Only Measured
10 = Remote 1 Temperature Only Measured
11 = Remote 2 Temperature Only Measured
<3:0>
Conversion Rates
These bits set how often the ADT7481 measures each temperature channel.
Conversion rates are as follows:
Conversions/sec
Time (seconds)
0000 = 0.0625
16
0001 = 0.125
8
0010 = 0.25
4
0011 = 0.5
2
0100 = 1
1
0101 = 2
500 m
0110 = 4
250 m
0111 = 8 = Default
125 m
1000 = 16
62.5 m
1001 = 32
31.25 m
1010 = 64
15.5 m
1011 = Continuous Measurements
73 m (Averaging Enabled)
Limit Registers
The ADT7481 has three limits for each temperature
channel: high, low, and THERM
temperature limits for
local, Remote 1, and Remote 2 temperature measurements.
The remote temperature high and low limits span two
registers each to contain an upper and lower byte for each
limit. There is also a THERM
hysteresis register. All limit
registers can be written to, and read back from, the SMBus.
See Table 16 for details of the limit register addresses and
power-on default values.
C will result in an out-of-limit condition, setting a flag in
the status register.
If the low limit register is programmed with 0癈,
measuring 0癈 or lower will result in an out-of-limit
condition.
Exceeding either the local or remote THERM
limit asserts
THERM
low. When Pin 8 is configured as THERM2
,
exceeding either the local or remote high limit asserts
THERM2
low. A default hysteresis value of 10癈 is
provided that applies to both THERM
channels. This
hysteresis value may be reprogrammed.
It is important to remember that the temperature limits
data format is the same as the temperature measurement data
format. So if the temperature measurement uses the default
binary scale, then the temperature limits also use the binary
scale. If the temperature measurement scale is switched,
however, the temperature limits do not automatically
switch.
The user must reprogram the limit registers to the desired
value in the correct data format. For example, if the remote
low limit is set at 10癈 and the default binary scale is being
used, the limit register value should be 0000 1010b. If the
scale is switched to offset binary, the value in the low
temperature limit register should be reprogrammed to be
0100 1010b.
Status Registers
The status registers are read-only registers, at
Address 0x02 (Status Register 1) and Address 0x23 (Status
Register 2). They contain status information for the
ADT7481.
Table 12. STATUS REGISTER 1 BIT ASSIGNMENTS
Bit
Mnemonic
Function
ALERT
7
BUSY
1 when ADC Converting
No
6
LHIGH
(Note 1)
1 when Local High
Temperature Limit Tripped
Yes
5
LLOW
(Note 1)
1 when Local Low
Temperature Limit Tripped
Yes
4
R1HIGH
1 when Remote 1 High
Temperature Limit Tripped
Yes
3
R1LOW
(Note 1)
1 when Remote 1 Low
Temperature Limit Tripped
Yes
2
D1 OPEN
(Note 1)
1 when Remote 1 Sensor
Open Circuit
Yes
1
R1THRM1
1 when Remote1 THERM
Limit Tripped
No
0
LTHRM1
1 when local THERM
Limit
Tripped
No
1. These flags stay high until the status register is read, or they are
reset by POR.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7482ARMZ-REEL | IC SENSOR TEMP 2CH ALARM 10MSOP |
| ADT7485AARMZ-R | IC TEMP/VOLT DGL SENS SST 10MSOP |
| ADT7486AARMZ-RL | IC TEMP SENS DGTL 2CH SST 10MSOP |
| ADT7488AARMZ-RL | IC TEMP/VOLT DGTL W/SST 10MSOP |
| ADT7518ARQZ | IC SENSOR TEMP QD ADC/DAC 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7481ARMZ-R7 | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-REEL | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-REEL7 | 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7481EBZEVB | 功能描述:EVALUATION BOARD ADT7481 制造商:on semiconductor 系列:* 零件狀態:在售 標準包裝:1 |
| ADT7482 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel Temperature Sensor and Overtemperature Alarm |
發布緊急采購，3分鐘左右您將得到回復。