- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7481ARMZ-1RL (ON Semiconductor)IC SENSOR TEMP 2CH ALARM 10MSOP Datasheet資料下載
參數資料
| 型號： | ADT7481ARMZ-1RL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 11/20頁 |
| 文件大小： | 237K |
| 描述： | IC SENSOR TEMP 2CH ALARM 10MSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 120°C，外部傳感器 |
| 精確度： | ±2.5°C（最小值） |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 120°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | ADT7481ARMZ-1REEL ADT7481ARMZ-1REEL-ND |
ADT7481
http://onsemi.com
11
Table 13. STATUS REGISTER 2 BIT ASSIGNMENTS
Bit
Mnemonic
Function
ALERT
7
Res
Reserved for Future Use
No
6
Res
Reserved for Future Use
No
5
Res
Reserved for Future Use
No
4
R2HIGH
(Note 1)
1 when Remote 2 High
Temperature Limit Tripped
Yes
3
R2LOW
(Note 1)
1 when Remote 2 Low
Temperature Limit Tripped
Yes
2
D2 OPEN
(Note 1)
1 when Remote 2 Sensor
Open Circuit
Yes
1
R2THRM1
1 when Remote 2 THERM
Limit Tripped
No
0
ALERT
1 when ALERT
Condition
Exists
No
1. These flags stay high until the status register is read, or they are
reset by POR.
The eight flags that can generate an ALERT
are NORd
together. When any flag is high, the ALERT
interrupt latch
is set and the ALERT
output goes low (provided that the
flag(s) is/are not masked out).
Reading the Status 1 register will clear the five flags (Bit 6
through Bit 2) in Status Register 1, provided the error
conditions that caused the flags to be set have gone away.
Reading the Status 2 register will clear the three flags (Bit 4
through Bit 2) in Status Register 2, provided the error
conditions that caused the flags to be set have gone away. A
flag bit can only be reset if the corresponding value register
contains an in-limit measurement, or if the sensor is good.
The ALERT
interrupt latch is not reset by reading the
status register. It will be reset when the ALERT
output has
been serviced by the master reading the device address,
provided the error condition has gone away and the status
register flag bits have been reset.
When Flag 1 and/or Flag 0 of Status Register 1, or Flag 1
of Status Register 2 are set, the THERM
output goes low to
indicate that the temperature measurements are outside the
programmed limits. The THERM
output does not need to be
reset, unlike the ALERT
output. Once the measurements are
within the limits, the corresponding status register bits are
reset automatically, and the THERM
output goes high. The
user may add hysteresis by programming Register 0x21.
The THERM
output will be reset only when the temperature
falls below the THERM
limit minus hysteresis.
When Pin 8 is configured as THERM2
, only the high
temperature limits are relevant. If Flag 6 and Flag 4 of Status
Register 1, or Flag 4 of Status Register 2 are set, the
THERM2
output goes low to indicate that the temperature
measurements are outside the programmed limits. Flag 5
and Flag 3 of Status Register 1, and Flag 3 of Status
Register 2 have no effect on THERM2
. The behavior of
THERM2
is otherwise the same as THERM
.
Bit 0 of Status Register 2 gets set whenever the ALERT
output is asserted low. Thus, the user need only read Status
Register 2 to determine if the ADT7481 is responsible for
the ALERT
. This bit gets reset when the ALERT
output gets
reset. If the ALERT
output is masked, then this bit is not set.
Offset Register
Offset errors may be introduced into the remote
temperature measurement by clock noise or by the thermal
diode being located away from the hot spot. To achieve the
specified accuracy on this channel, these offsets must be
removed.
The offset values are stored as 10-bit, twos complement
values.
" The Remote 1 offset MSBs are stored in Register 0x11
and the LSBs are stored in Register 0x12 (low byte, left
justified).
" The Remote 2 offset MSBs are stored in Register 0x34
and the LSBs are stored in Register 0x35 (low byte, left
justified). The Remote 2 offset can be written to, or
read from, the Remote 1 offset registers if Bit 3 of the
Configuration 1 register is set to 1. This bit should be
set to 0 (default) to read the Remote 1 offset values.
Only the upper two bits of the LSB registers are used. The
MSB of the MSB offset register is the sign bit. The minimum
offset that can be programmed is 128癈, and the maximum
is +127.75癈. The value in the offset register is added to, or
subtracted from, the measured value of the remote
temperature.
The offset register powers up with a default value of 0癈
and will have no effect unless the user writes a different
value to it.
Table 14. SAMPLE OFFSET REGISTER CODES
Offset Value
0x11/0x34
0x12/0x35
128癈
1000 0000
00 00 0000
4癈
1111 1100
00 00 0000
1癈
1111 1111
00 000000
0.25癈
1111 1111
10 00 0000
0癈
0000 0000
00 00 0000
+0.25癈
0000 0000
01 00 0000
+1癈
0000 0001
00 00 0000
+4癈
0000 0100
00 00 0000
+127.75癈
0111 1111
11 00 0000
One-shot Register
The one-shot register is used to initiate a conversion and
comparison cycle when the ADT7481 is in standby mode,
after which the device returns to standby. Writing to the
one-shot register address (0x0F) causes the ADT7481 to
perform a conversion and comparison on both the local and
the remote temperature channels. This is not a data register
as such, and it is the write operation to Address 0x0F that
causes the one-shot conversion. The data written to this
address is irrelevant and is not stored. However the ALERT
and THERM
outputs are not operational in one-shot mode
and should not be used.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7482ARMZ-REEL | IC SENSOR TEMP 2CH ALARM 10MSOP |
| ADT7485AARMZ-R | IC TEMP/VOLT DGL SENS SST 10MSOP |
| ADT7486AARMZ-RL | IC TEMP SENS DGTL 2CH SST 10MSOP |
| ADT7488AARMZ-RL | IC TEMP/VOLT DGTL W/SST 10MSOP |
| ADT7518ARQZ | IC SENSOR TEMP QD ADC/DAC 16QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7481ARMZ-R7 | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-REEL | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-REEL7 | 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7481EBZEVB | 功能描述:EVALUATION BOARD ADT7481 制造商:on semiconductor 系列:* 零件狀態:在售 標準包裝:1 |
| ADT7482 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel Temperature Sensor and Overtemperature Alarm |
發布緊急采購，3分鐘左右您將得到回復。