- 您現在的位置：買賣IC網 > PDF目錄374040 > ADUC848BS8-5 (ANALOG DEVICES INC) MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU PDF資料下載
參數資料
| 型號： | ADUC848BS8-5 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| 中文描述： | 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | 14 X 14 MM, PLASTIC, MO-112-AC-1, MQFP-52 |
| 文件頁數： | 33/108頁 |
| 文件大小： | 1109K |
| 代理商： | ADUC848BS8-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
ADuC845/ADuC847/ADuC848
can be taken. When the resulting voltage measured is full scale,
the transducer has gone open circuit. When the voltage measured
is 0 V, this indicates that the transducer has gone short circuit.
The current sources work over the normal absolute input
voltage range specifications.
Rev. A | Page 33 of 108
REFERENCE DETECT CIRCUIT
The main and auxiliary (ADuC845 only) ADCs can be
configured to allow the use of the internal band gap reference or
an external reference that is applied to the REFIN± pins by
means of the XREF0/1 bit in the Control Registers AD0CON2
and AD1CON (ADuC845 only). A reference detection circuit is
provided to detect whether a valid voltage is applied to the
REFIN± pins. This feature arose in connection with strain-gage
sensors in weigh scales where the reference and signal are
provided via a cable from the remote sensor. It is desirable to
detect whether the cable is disconnected. If either of the pins is
floating or if the applied voltage is below a specified threshold, a
flag (NOXREF) is set in the ADC status register (ADCSTAT),
conversion results are clamped, and calibration registers are not
updated if a calibration is in progress.
Note that the reference detect does not look at REFIN2± pins.
If, during either an offset or gain calibration, the NOEXREF bit
becomes active, indicating a incorrect V
REF
, updating the relevant
calibration register is inhibited to avoid loading incorrect data
into these registers, and the appropriate bits in ADCSTAT (ERR0
or ERR1) are set. If the user needs to verify that a valid
reference is in place every time a calibration is performed, the
status of the ERR0 and ERR1 bits should be checked at the end
of every calibration cycle.
SINC FILTER REGISTER (SF)
The number entered into the SF register sets the decimation
factor of the Sinc
3
filter for the ADC. See Table 28 and Table 29.
The range of operation of the SF word depends on whether
ADC chop is on or off. With chop disabled, the minimum SF
word is 3 and the maximum is 255. This gives an ADC through-
put rate from 16.06 Hz to 1.365 kHz. With chop enabled, the
minimum SF word is 13 (all values lower than 13 are clamped
to 13) and the maximum is 255. This gives an ADC throughput
rate of from 5.4 Hz to 105 Hz. See the f
ADC
equation in the ADC
description preceding section.
An additional feature of the Sinc
3
filter is a second notch filter
positioned in the frequency response at 60 Hz. This gives
simultaneous 60 Hz rejection to whatever notch is defined by
the SF filter. This 60 Hz filter is enabled via the REJ60 bit in the
ADCMODE register (ADCMODE.6). The notch is valid only
for SF words ≥ 68; otherwise, ADC errors occur, and, in fact, the
notch is best used with an SF word of 82d giving simultaneous
50 Hz and 60 Hz rejection. This function is useful only with an
ADC clock (modulator rate) of 32.768 kHz. During calibration,
the current (user-written) value of the SF register is used.
Σ-
MODULATOR
A Σ- ADC usually consists of two main blocks, an analog
modulator, and a digital filter. For the ADuC845/ADuC847/
ADuC848, the analog modulator consists of a difference
amplifier, an integrator block, a comparator, and a feedback
DAC as shown in Figure 16.
INTEGRATOR
COMPARATOR
DIFFERENCE
AMP
ANALOG
INPUT
HIGH
FREQUENCY
BIT STREAM
TO DIGITAL
FILTER
DAC
0
Figure 16. Σ- Modulor Simplified Block Diagram
In operation, the analog signal is fed to the difference amplifier
along with the output from the feedback DAC. The difference
between these two signals is integrated and fed to the comparator.
The output from the comparator provides the input to the feed-
back DAC so the system functions as a negative feedback loop
that tries to minimize the difference signal. The digital data that
represents the analog input voltage is contained in the duty
cycle of the pulse train appearing at the output of the comparator.
This duty cycle data can be recovered as a data-word by using a
subsequent digital filter stage. The sampling frequency of the
modulator loop is many times higher than the bandwidth of the
input signal. The integrator in the modulator shapes the
quantization noise (that results from the analog-to-digital
conversion) so that the noise is pushed toward one-half of the
modulator frequency.
DIGITAL FILTER
The output of the ∑- modulator feeds directly into the digital
filter. The digital filter then band-limits the response to a
frequency significantly lower than one-half of the modulator
frequency. In this manner, the 1-bit output of the comparator is
translated into a band-limited, low noise output from the part.
The ADuC845/ADuC847/ADuC848 filter is a low-pass, Sinc
3
or
[(SINx)/x]
3
filter whose primary function is to remove the
quantization noise introduced at the modulator. The cutoff
frequency and decimated output data rate of the filter are
programmable via the SF (Sinc filter) SFR as listed in Table 28
and Table 29.
Figure 22, Figure 23, Figure 24, and Figure 25 show the frequency
response of the ADC, yielding an overall output rate of 16.6 Hz
with chop enabled and 50 Hz with chop disabled. Also detailed
in these plots is the effect of the fixed 60 Hz drop-in notch filter
(REJ60 bit, ADCMODE.6). This fixed filter can be enabled or
disabled by setting or clearing the REJ60 bit in the ADCMODE
register (ADCMODE.6). This 60 Hz drop-in notch filter can be
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC845 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC845BCP8-3 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC847BCP8-3 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC845BCP8-5 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC847BCP8-5 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC848BSZ32-3 | 功能描述:IC MCU FLASH W/16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC848BSZ32-5 | 功能描述:IC MCU FLASH W/16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC848BSZ62-3 | 功能描述:IC MCU FLASH W/16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
| ADUC848BSZ62-5 | 功能描述:IC FLASH MCU W/16BIT ADC 52MQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:250 系列:LPC11Uxx 核心處理器:ARM? Cortex?-M0 芯體尺寸:32-位 速度:50MHz 連通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外圍設備:欠壓檢測/復位，POR，WDT 輸入/輸出數:40 程序存儲器容量:96KB（96K x 8） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-LQFP 包裝:托盤 其它名稱:568-9587 |
| ADUC848BSZ62-5 REEL MTL | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。