- 您現在的位置：買賣IC網 > Datasheet目錄39 > AT30TSE002B-MAH-T (Atmel)SENSOR DGTL TEMP I2C/SMBUS 8WDFN Datasheet資料下載
參數資料
| 型號： | AT30TSE002B-MAH-T |
| 廠商： | Atmel |
| 文件頁數： | 11/36頁 |
| 文件大小： | 1184K |
| 描述： | SENSOR DGTL TEMP I2C/SMBUS 8WDFN |
| 標準包裝： | 5,000 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
11
Atmel AT30TSE002B [DATASHEET]
8711GSEEPR5/12
9.
EEPROM Write Protection
The device supports permanent and reversible software write protection and once enabled, write protects the first-half of
the array (00H - 7FH).
Permanent Software Write Protection: The software write protection is enabled by sending a command similar to a
normal write command; to the device which programs the permanent write protect register. The write protect register is
programmed by sending a write command with the device address of 0110 with the address and data bit being dont
cares (see Figure 12-5 and Table 12-1). Once the software write protection has been enabled, the device will no longer
acknowledge the 0110 control byte. The software write protection cannot be reversed even if the device is powered
down. The write cycle time must be observed.
Reversible Software Write Protection: The reversible software write protection is enabled by sending a command,
similar to a normal write command; to the device which programs the reversible write protect register. The write protect
register is programmed by sending a write command 01100010 with pins A
2
and A
1
tied to ground or no connect and pin
A
0
connected to V
HV
(see Figure 12-6 and Table 12-1). The reversible write protection can be reversed by sending a
command 01100110 with pin A
2
tied to ground or no connect, pin A
1
tied to V
CC
and pin A
0
tied to V
HV
(see Figure 12-6
and Table 12-1).
10. Temperature Sensor Functional Description
AT30TSE002B consists of a Delta-Sigma Analog to Digital Converter (ADC) with a band gap type temperature sensor
that monitors and updates its own temperature reading at least eight times per second converting the readings into digital
data bits and latching them into a temperature register that can be read via 2-wire I
2
C/SMBus serial interface. The device
communicates over a 2-wire I
2
C/SMBus interface with the bus master or controller consisting of a serial clock (SCL) and
serial bidirectional data bus (SDA) with clock frequencies up to 400Khz. The bus master or controller generates the SCL
signal and is used by the AT30TSE002B to receive and send serial data on the SDA line with the most significant bit
transferred first. A pull-up resistor is required on the SDA pin since it has an open drain configuration.
10.1
EVENT Output
The
EVENT pin has three operating modes depending on configuration settings. They are Interrupt, Comparator, and
Critical Alarm (Crit_Alarm) modes.
In the Interrupt mode, once a temperature reaches a boundary limit, the AT30TSE002B asserts the
EVENT pin. The
EVENT pin will remain asserted until software clears the interrupt by writing a one to the EVTCLR bit five in the
configuration register. When the temperature drops below specified limits, the device returns back to either interrupt or
comparator mode as programmed in the configuration registers EVTMOD bit zero.
In the comparator mode, the
EVENT pin remains asserted until the error condition that caused the pin to be asserted no
longer exists and the
EVENT pin will clear itself. In the Crit_Alarm mode, when the measured temperature exceeds
Crit_Alarm trip limit, the
EVENT pin will remain asserted until the temperature drops below Crit_Alarm limit minus
hysteresis (See Figure 11-1). All event thresholds use hysteresis as programmed in the configuration register.
10.2 Alarm Window
The alarm window consists of the Upper Alarm Trip Register and Lower Alarm Trip Register. The Upper Alarm Trip
Register holds the upper temperature trip point and the Lower Alarm Trip Register holds the lower temperature trip point.
After the
EVENT pin control is enabled, the
EVENT output will be triggered upon entering and exiting from this window.
相關PDF資料 |
PDF描述 |
|---|---|
| BD3504FVM-TR | IC REG CTRLR SGL POS ADJ 8MSOP |
| BD3521FVM-TR | IC REG CTRLR SGL 1.5V MSOP8 |
| BD9153MUV-E2 | IC REG TRPL BCK/LINEAR 24VQFN |
| CAT2300VP2-GT3 | IC SENSE FET CONTROLLER 8TDFN |
| CAT34TS02VP2GT4A | IC TEMP SENSOR 2K MEMORY 8TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT30TSE004A-MA5M-T | 制造商:Atmel Corporation 功能描述:1-CH TMPSNSR, 4K SPD EE, I2C, 1.7V-3.6V - 1MHZ, EXTENDED TEM - Tape and Reel 制造商:Adesto Technologies Corporation 功能描述: 制造商:Atmel Corporation 功能描述:SENSOR DGTL TEMP I2C/SMBUS 8UDFN 制造商:Atmel Corporation 功能描述:1-ch TmpSnsr, 4K SPD EE, I2C, 1.7V-3.6V - 1MHz, Extended Temp, 8-UDFN |
| AT30TSE004A-MAA5AK-T | 功能描述:1.7-3.6V, 1MHZ, EXT TMP, 8-WDFN 制造商:atmel 系列:- 包裝:剪切帶（CT） 零件狀態:停產 傳感器類型:數字，本地 檢測溫度 - 本地:-20°C ~ 125°C 檢測溫度 - 遠程:- 輸出類型:I2C 電壓 - 電源:1.7 V ~ 3.6 V 分辨率:11 b 特性:可編程極限，可選擇滯后，關斷模式，待機模式 精度 - 最高（最低）:±1°C（±3°C） 測試條件:75°C ~ 95°C（-20°C ~ 125°C） 工作溫度:-20°C ~ 125°C 封裝/外殼:8-WFDFN 裸露焊盤 供應商器件封裝:8-WDFN（2x3） 標準包裝:1 |
| AT30TSE004A-MAA5M-T | 制造商:Atmel Corporation 功能描述:TMP SENSOR EEP RWP 512X8 1.7-3.6V 8UDFN NG - Tape and Reel 制造商:Atmel Corporation 功能描述:TMP SENSOR EEP RWP 512X8 1.7-3.6V 8UDFN NG - Cut TR (SOS) 制造商:Adesto Technologies Corporation 功能描述: 制造商:Atmel Corporation 功能描述:SENSOR DGTL TEMP I2C/SMBUS 8WDFN 制造商:Atmel Corporation 功能描述:Board Mount Temperature Sensors 1-ch TmpSnsr 4K SPEE I2C 1.7V-3.6V-1MHz 制造商:Atmel Corporation 功能描述:1-ch TmpSnsr, 4K SPD EE, I2C, 1.7V-3.6V - 1MHz, Extended Temp, 8-WDFN |
| AT30TSE004-MA5M-T | 制造商:Atmel Corporation 功能描述:SERIAL ANALOG, TEMP SENSOR - 8 制造商:Atmel Corporation 功能描述:SERIAL ANALOG, TEMP SENSOR - 8 UDFN,TMP SENSOR,PB/HALOFREE,N - Tape and Reel |
| AT30TSE004-MAA5M-T | 制造商:Atmel Corporation 功能描述:SERIAL ANALOG, TEMP SENSOR - 8 制造商:Atmel Corporation 功能描述:SERIAL ANALOG, TEMP SENSOR - 8 WDFN,TMP SENSOR,PB/HALOFREE,N - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。