欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CCW1152-0629-34AB95L
元件分類: 插座
英文描述: BGA1152, IC SOCKET
封裝: ROHS COMPLIANT
文件頁數: 3/8頁
文件大小: 1320K
代理商: CCW1152-0629-34AB95L
Socket Mounting Recommendations and Reflow Profile
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland
Phone +41-21-781 08 10 www.e-tec.com info@e-tec.com
E-tec Socket Mounting Recommendations
PRELIMINARY
1
Purpose
This document is meant to serve as a guide for mounting E-tec surface mount device (SMD)
sockets to the printed circuit board (PCB). The recommendations described here are guidelines
only, and modifications may be needed for your particular socket, PCB, and process.
Application
The sockets this document applies to are as follows: Clam Shell, Knob Lock, Screw Lock, Twist
Lock, Quick Lock and Lever Lock in SMD style. These sockets utilize the E-tec patented spring-
pin technology. This technology allows the pins to be soldered to the PCB while still providing
compliance to the device under test (DUT) via springs located at the other end of the pin. The
pins themselves do not have solder pre-forms as a BGA would with its solder balls. However, the
sockets are designed to mount to the same PCB footprint and pads as required by the BGA, or
any other IC package the socket was designed for (except if locating pegs are used; see ‘Locating
Pegs’ section of this document). When compared to mounting a BGA, an extra volume of solder
paste is required to mount the sockets to the PCB. To effect this, a properly dimensioned stencil
is required. Once the paste has been applied, a standard reflow process is then used to solder the
socket to the PCB. After the socket is verified to have proper electrical connection to the PCB,
the system is then ready to be used.
Locating Pegs
Although designed to mount to the same footprint as the IC, with just a small amount of
additional keep-out area, E-tec sockets can also be offered with locating pegs. The sockets are
typically mounted with two locating pegs, which require two thru-holes drilled into the PCB.
These pegs help to align the socket on the PCB, and hence align the socket’s pins to the PCB’s
pads, during the soldering process. Furthermore, plating the thru-holes allows the locating pegs
to be soldered to the PCB for better mechanical stability during everyday use and handling of the
socket. If the PCB design permits, E-tec recommends the use of these locating pegs. For fine-
pitch, low pin-count sockets without locating pegs, the mechanical strength of the solder joints
may be insufficient. In these cases, it is recommended to epoxy the socket body to the PCB. 3M
Scotch-Weld 2216 B/A is a suitable epoxy. In any case, the proper volume of solder paste is
required to ensure mechanical and electrical integrity. Recommended stencil dimensions are
given in the next section of this document.
相關PDF資料
PDF描述
CS209-49GT PGA289, IC SOCKET
CS212-29GG PGA392, IC SOCKET
CS262-49GT PGA302, IC SOCKET
CS264-04GT PGA384, IC SOCKET
CS239-51GG PGA339, IC SOCKET
相關代理商/技術參數
參數描述
CCW115R0JLFTR 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 15 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW116R0JLFTR 制造商:IRC 功能描述:16 OHM 1W 5% WW 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 16 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW118R0JLFTR 制造商:IRC 功能描述:18 OHM 1W 5% WW 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 18 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW-1-1R00-G-LF-BLK 制造商:IRCTT 制造商全稱:IRC - a TT electronics Company. 功能描述:Commercial Grade Power Axial Wirewound Resistor
CCW-1-1R00-J-LF-BLK 制造商:IRCTT 制造商全稱:IRC - a TT electronics Company. 功能描述:Commercial Grade Power Axial Wirewound Resistor
主站蜘蛛池模板: 云霄县| 阜阳市| 黄梅县| 桐城市| 无极县| 昭觉县| 怀远县| 布尔津县| 城市| 乌拉特后旗| 曲靖市| 韶山市| 张家界市| 高台县| 光山县| 卢氏县| 曲松县| 阿克陶县| 海门市| 灵宝市| 石泉县| 公主岭市| 合阳县| 莆田市| 和田县| 哈密市| 沈丘县| 龙川县| 安西县| 郯城县| 高邮市| 贞丰县| 靖宇县| 大同市| 泰来县| 榆社县| 津市市| 三门峡市| 青河县| 嘉祥县| 江门市|