欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: CCW1152-0629-34AB95L
元件分類: 插座
英文描述: BGA1152, IC SOCKET
封裝: ROHS COMPLIANT
文件頁數: 6/8頁
文件大小: 1320K
代理商: CCW1152-0629-34AB95L
Socket Mounting Recommendations and Reflow Profile
E-tec Interconnect Ltd, Industrial Zone C, CH-1072 Forel (Lavaux), Switzerland
Phone +41-21-781 08 10 www.e-tec.com info@e-tec.com
E-tec Socket Mounting Recommendations
PRELIMINARY
4
Verifying the Assembly
After the socket has been reflowed to the PCB, open and short testing should be partaken to
ensure proper assembly. The assembly house typically performs x-ray inspection to verify non-
shorting of pins. However, as this is only a visual inspection, we recommend using a continuity
tester or ohmmeter and simply sweeping random rows and columns of pins to ensure no shorting
of pins. No damage to the springs will occur if very slight pressure from the meter’s tips is
applied (just touch the probes to the springs). For fine pitch sockets, a microscope would be
helpful in placing the meter’s tips appropriately.
After verifying the absence of shorts, open testing should be performed. The most direct, yet
tedious, method is to use the continuity tester to directly probe each pin to a breakout or test
point on the board. Again no damage will occur if the probes are touched to the springs. If heavy
pressure is required to push the socket body towards the PCB to achieve continuity, this means a
poor solder joint. If no such test points exist, then the BGA’s via field on the backside of the
PCB should be kept solder-mask free to allow for such probing. If the via field is kept open, a
simpler open testing method can be performed. Simply use a wet sponge (or some other
conductive material) and hold it onto the via field. This shorts all the pins together on the PCB.
Insert one probe of the continuity tester into the sponge. Now sweep the pins of the socket with
the other probe and check for continuity.
If the above procedures show any shorts or opens, then it is advisable to have the assembly house
re-evaluate the assembly method used. An incorrect stencil can lead to too much or too little
solder paste, easily leading short or open conditions and a solder paste with Ag contents
(>=0.5%) may also result in solder joint failures. These are the primary reasons for socket
mounting failures.
Important Notes:
a) Screw/Twist Lock Socket
When tightening the lid of a Screw or Twist Lock socket, it is imperative to not over-tighten the
retention screws, otherwise irreparable damage may occur. Such damage is not covered by
warranty and will be solely the end user’s responsibility. The maximum allowed torque on these
retention screws is 7cN-m (10oz-in) for sockets up to 800 pins and for sockets as of 800 pins the
torque value needs to be increased but should not exceed a maximum of 10cN-m (14oz-in). E-tec
sells the torque screwdriver TOL-7CN-TORQUE which is preset to 7cN-m, but which can be
adjusted to higher torque values for the high pin count sockets.
相關PDF資料
PDF描述
CS209-49GT PGA289, IC SOCKET
CS212-29GG PGA392, IC SOCKET
CS262-49GT PGA302, IC SOCKET
CS264-04GT PGA384, IC SOCKET
CS239-51GG PGA339, IC SOCKET
相關代理商/技術參數
參數描述
CCW115R0JLFTR 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 15 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW116R0JLFTR 制造商:IRC 功能描述:16 OHM 1W 5% WW 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 16 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW118R0JLFTR 制造商:IRC 功能描述:18 OHM 1W 5% WW 制造商:TT Electronics / IRC 功能描述:CCW Series 1 W 18 Ohms 5 % Commercial Grade Power Axial Wirewound Resistor
CCW-1-1R00-G-LF-BLK 制造商:IRCTT 制造商全稱:IRC - a TT electronics Company. 功能描述:Commercial Grade Power Axial Wirewound Resistor
CCW-1-1R00-J-LF-BLK 制造商:IRCTT 制造商全稱:IRC - a TT electronics Company. 功能描述:Commercial Grade Power Axial Wirewound Resistor
主站蜘蛛池模板: 桐庐县| 静海县| 辽阳市| 延庆县| 巴中市| 鹤岗市| 扶绥县| 义马市| 抚州市| 孟州市| 伊川县| 沽源县| 余姚市| 平南县| 和林格尔县| 南华县| 哈密市| 顺平县| 海宁市| 隆安县| 安泽县| 视频| 山东省| 随州市| 华蓥市| 神池县| 花垣县| 邻水| 从化市| 永丰县| 葵青区| 汕尾市| 沛县| 谢通门县| 托克逊县| 纳雍县| 台南县| 綦江县| 乌拉特中旗| 潞城市| 三明市|