- 您現在的位置：買賣IC網 > PDF目錄19022 > DC1370A-K (Linear Technology)BOARD DEMO 40MSPS LTC2257-12 PDF資料下載
參數資料
| 型號： | DC1370A-K |
| 廠商： | Linear Technology |
| 文件頁數： | 19/34頁 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 40MSPS LTC2257-12 |
| 軟件下載： | QuikEval II System |
| 設計資源： | DC1370A Design Files |
| 標準包裝： | 1 |
| 系列： | * |
| 相關產品： | DC718C-ND - DEMO QUIKEVAL-II DATA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LTC2258-12
LTC2257-12/LTC2256-12
26
225812fd
For more information www.linear.com/LTC2258-12
applicaTions inForMaTion
Serial Programming Mode
To use the serial programming mode, PAR/SER should be
tied to ground. The CS, SCK, SDI and SDO pins become a
serialinterfacethatprogramtheA/Dmodecontrolregisters.
Data is written to a register with a 16-bit serial word. Data
can also be read back from a register to verify its contents.
Serial data transfer starts when CS is taken low. The data
on the SDI pin is latched at the first 16 rising edges of
SCK. Any SCK rising edges after the first 16 are ignored.
The data transfer ends when CS is taken high again.
The first bit of the 16-bit input word is the R/W bit. The
next seven bits are the address of the register (A6:A0).
The final eight bits are the register data (D7:D0).
If the R/W bit is low, the serial data (D7:D0) will be writ-
ten to the register set by the address bits (A6:A0). If the
R/W bit is high, data in the register set by the address bits
(A6:A0) will be read back on the SDO pin (see the timing
diagrams). During a read back command the register is
not updated and data on SDI is ignored.
The SDO pin is an open-drain output that pulls to ground
with a 200 impedance. If register data is read back
through SDO, an external 2k pull-up resistor is required. If
serial data is only written and read back is not needed, then
SDO can be left floating and no pull-up resistor is needed.
Table 3 shows a map of the mode control registers.
Software Reset
If serial programming is used, the mode control registers
shouldbeprogrammedassoonaspossibleafterthepower
supplies turn on and are stable. The first serial command
must be a software reset which will reset all register data
bits to logic 0. To perform a software reset, bit D7 in the
reset register is written with a logic 1. After the reset SPI
write command is complete, bit D7 is automatically set
back to zero.
Table 3. Serial Programming Mode Register Map
REGISTER A0: RESET REGISTER (ADDRESS 00h)
D7
D6
D5
D4
D3
D2
D1
D0
RESET
X
Bit 7
RESET
Software Reset Bit
0 = Not Used
1 = Software Reset. All Mode Control Registers are Reset to 00h. This Bit is Automatically Set Back to Zero at the End of the SPI
Write Command.
The Reset Register is Write Only.
Bits 6-0
Unused, Don’t Care Bits.
REGISTER A1: POWER-DOWN REGISTER (ADDRESS 01h)
D7
D6
D5
D4
D3
D2
D1
D0
X
PWROFF1
PWROFF0
Bits 7-2
Unused, Don’t Care Bits.
Bits 1-0
PWROFF1:PWROFF0
Power Down Control Bits
00 = Normal Operation
01 = Nap Mode
10 = Not Used
11 = Sleep Mode
相關PDF資料 |
PDF描述 |
|---|---|
| 7239 | LAMP INCAND T-1 5V SUB MIDGET |
| A3CT-7111 | SWITCH UNIT-IP40 |
| 1.30242.2122200 | SWITCH SEL LTCH ILLM 1X90 FORM V |
| DC1369A-G | BOARD DEMO 125MSPS LTC2261-12 |
| 8097 | T-1 12V .050" BI-PIN BASE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1370A-L | 功能描述:BOARD DEMO 25MSPS LTC2256-12 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC1370A-M | 制造商:Linear Technology 功能描述:14BIT ADC Eval Brd, Rq. DC718 制造商:Linear Technology 功能描述:14BIT ADC Eval Brd, Rq. DC718; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2262-14; Kit Application Type:Data Converter; Application Sub Type:ADC; Kit Contents:Board, Guide; Features:Also works with requred DC718 |
| DC1370A-N | 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC718 制造商:Linear Technology 功能描述:12BIT ADC Eval Brd, Rq. DC718; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC2262-12; Kit Application Type:Data Converter; Application Sub Type:ADC; Kit Contents:Board, Guide; Features:Also works with requred DC718 |
| DC1371A | 功能描述:BOARD USB DATA ACQUISITION HS RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC1379A | 功能描述:BOARD EVAL LTM8025 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:µModule® 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
發布緊急采購，3分鐘左右您將得到回復。