欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： DSPIC33FJ32GP202T-I/SO
廠商： Microchip Technology
文件頁數： 117/176頁
文件大小： 0K
描述： IC DSPIC MCU/DSP 32K 28SOIC
產品培訓模塊： Asynchronous Stimulus
標準包裝： 1,600
系列： dsPIC™ 33F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 40 MIP
連通性： I²C，IrDA，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 21
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 10x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
包裝： 帶卷 (TR)
配用： DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
其它名稱： DSPIC33FJ32GP202T-I/SOTR
2007-2011 Microchip Technology Inc.
DS70290J-page 45
dsPIC33FJ32GP202/204 and dsPIC33FJ16GP304
4.4.1
SOFTWARE STACK
In addition to its use as a working register, the W15
register
in
the
dsPIC33FJ32GP202/204
and
dsPIC33FJ16GP304 devices is also used as a
software Stack Pointer. The Stack Pointer always
points to the first available free word and grows from
lower to higher addresses. It pre-decrements for stack
pops and post-increments for stack pushes, as shown
in Figure 4-4. For a PC push during any CALL
instruction, the MSB of the PC is zero-extended before
the push, ensuring that the MSB is always clear.
The Stack Pointer Limit register (SPLIM) associated
with the Stack Pointer sets an upper address boundary
for the stack. SPLIM is uninitialized at Reset. As is the
case for the Stack Pointer, SPLIM<0> is forced to ‘0’
because all stack operations must be word-aligned.
When an EA is generated using W15 as a source or
destination pointer, the resulting address is compared
with the value in SPLIM. If the contents of the Stack
Pointer (W15) and the SPLIM register are equal and a
push operation is performed, a stack error trap will not
occur. The stack error trap will occur on a subsequent
push operation. For example, to cause a stack error
trap when the stack grows beyond address 0x1000 in
RAM, initialize the SPLIM with the value 0x0FFE.
Similarly, a Stack Pointer underflow (stack error) trap is
generated when the Stack Pointer address is found to
be less than 0x0800. This prevents the stack from
interfering with the Special Function Register (SFR)
space.
A write to the SPLIM register should not be immediately
followed by an indirect read operation using W15.
FIGURE 4-4:
CALL STACK FRAME
4.4.2
DATA RAM PROTECTION FEATURE
The dsPIC33F product family supports Data RAM
protection features that enable segments of RAM to be
protected when used in conjunction with Boot and
Secure Code Segment Security. BSRAM (Secure RAM
segment for Boot Segment) is accessible only from the
Boot Segment Flash code when enabled. SSRAM
(Secure RAM segment for RAM) is accessible only
from the Secure Segment Flash code when enabled.
See Table 4-1 for an overview of the BSRAM and
SSRAM SFRs.
4.5
Instruction Addressing Modes
The addressing modes shown in Table 4-23 form the
basis of the addressing modes optimized to support the
specific features of individual instructions. The
addressing modes provided in the MAC class of
instructions differ from those in the other instruction
types.
4.5.1
FILE REGISTER INSTRUCTIONS
Most file register instructions use a 13-bit address field
(f) to directly address data present in the first 8192
bytes of data memory (Near Data Space). Most file
register instructions employ a working register, W0,
which is denoted as WREG in these instructions. The
destination is typically either the same file register or
WREG (with the exception of the MUL instruction),
which writes the result to a register or register pair. The
MOV instruction allows additional flexibility and can
access the entire data space.
4.5.2
MCU INSTRUCTIONS
The three-operand MCU instructions are of the form:
Operand 3 = Operand 1 <function> Operand 2
where:
Operand 1 is always a working register (that is, the
addressing mode can only be register direct), which is
referred to as Wb.
Operand 2 can be a W register, fetched from data
memory, or a 5-bit literal.
The result location can be either a W register or a data
memory location. The following addressing modes are
supported by MCU instructions:
Register Direct
Register Indirect
Register Indirect Post-Modified
Register Indirect Pre-Modified
5-bit or 10-bit Literal
Note:
A PC push during exception processing
concatenates the SRL register to the MSB
of the PC prior to the push.
<Free Word>
PC<15:0>
000000000
0
15
W15 (before CALL)
W15 (after CALL)
S
ta
ck
Gr
ow
sT
o
war
d
H
igh
er
A
ddr
es
s
0x0000
PC<22:16>
POP : [--W15]
PUSH : [W15++]
Note:
Not all instructions support all the
addressing
modes
given
above.
Individual
instructions
can
support
different subsets of these addressing
modes.
相關PDF資料
PDF描述
REC5-2405DRWZ/H/B/M/SMD-R CONV DC/DC 5W 9-36VIN +/-05VOUT
P51-750-A-S-D-4.5OVP-000-000 SENSOR 750PSI 1/4-18NPT .5-4.5V
70G-ODC24A OUTPUT MODULE DC G5 9MA 24VDC
20P2218 PANEL INNER 22X18" WHITE
PJSPU1816 PANEL SWING PJU 17.90X15.99"
相關代理商/技術參數
參數描述
dsPIC33FJ32GP204-E/ML 功能描述:數字信號處理器和控制器 - DSP, DSC 16B DSC 44LD32KB 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ32GP204-E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16B DSC 32KB 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ32GP204-H/ML 功能描述:數字信號處理器和控制器 - DSP, DSC 16 bit DSC 20MIPS 32KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ32GP204-H/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16 bit DSC 20MIPS 32KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ32GP204-I/ML 功能描述:數字信號處理器和控制器 - DSP, DSC 16B DSC 44LD 32KB Flash40 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 大城县| 滨海县| 册亨县| 汕头市| 大田县| 海阳市| 宾川县| 灵台县| 财经| 邮箱| 微博| 丹巴县| 紫金县| 山东省| 贺州市| 日喀则市| 大新县| 额尔古纳市| 祥云县| 图们市| 玉树县| 南宁市| 宁夏| 金昌市| 分宜县| 台北市| 诸城市| 天等县| 山阳县| 包头市| 南城县| 巴中市| 三亚市| 沙洋县| 临桂县| 石台县| 分宜县| 屯留县| 宜兰市| 鄢陵县| 鹿泉市|