- 您現在的位置：買賣IC網 > PDF目錄18702 > EFM32-TG210F32-SK (Energy Micro)IC MICRO KIT GECKO 32QFN PDF資料下載
參數資料
| 型號： | EFM32-TG210F32-SK |
| 廠商： | Energy Micro |
| 文件頁數： | 62/136頁 |
| 文件大小： | 0K |
| 描述： | IC MICRO KIT GECKO 32QFN |
| 標準包裝： | 1 |
| 系列： | Tiny Gecko |
| 套件類型： | 微控制器 |
| 值： | 2 件 - 閃存 - 32KB |
| 包裝： | 紙板盒 |
| 安裝類型： | 表面貼裝 |
| 包括封裝： | 32-QFN |
| 工具箱內容： | (2) 914-1034-2-ND - MCU 32BIT 32KB FLASH 32-QFN |
| 其它名稱： | 914-1019 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
...the world's most energy friendly microcontrollers
2011-02-04 - d0002_Rev1.00
31
www.energymicro.com
if the register is 0 the processor stops executing instructions and enters sleep mode
if the register is 1 the processor clears the register to 0 and continues executing instructions without
entering sleep mode.
See Section 3.10.11 (p. 86) for more information.
If the event register is 1, this indicate that the processor must not enter sleep mode on execution
of a WFE instruction. Typically, this is because the processor has executed an SEV instruction, see
Section 3.10.9 (p. 85) . Software cannot access this register directly.
2.5.1.3 Sleep-on-exit
If the SLEEPONEXIT bit of the SCR is set to 1, when the processor completes the execution of an
exception handler it returns to Thread mode and immediately enters sleep mode. Use this mechanism
in applications that only require the processor to run when an exception occurs.
2.5.2 Wakeup from sleep mode
The conditions for the processor to wakeup depend on the mechanism that cause it to enter sleep mode.
2.5.2.1 Wakeup from WFI or sleep-on-exit
Normally, the processor wakes up only when it detects an exception with sufficient priority to cause
exception entry.
Some embedded systems might have to execute system restore tasks after the processor wakes up, and
before it executes an interrupt handler. To achieve this set the PRIMASK bit to 1 and the FAULTMASK
bit to 0. If an interrupt arrives that is enabled and has a higher priority than current exception priority,
the processor wakes up but does not execute the interrupt handler until the processor sets PRIMASK
to zero. For more information about PRIMASK and FAULTMASK see Section 2.1.3.6 (p. 11) .
2.5.2.2 Wakeup from WFE
The processor wakes up if:
it detects an exception with sufficient priority to cause exception entry
in a multiprocessor system, another processor in the system executes an SEV instruction.
In addition, if the SEVONPEND bit in the SCR is set to 1, any new pending interrupt triggers an event and
wakes up the processor, even if the interrupt is disabled or has insufficient priority to cause exception
entry. For more information about the SCR see Section 4.3.7 (p. 100) .
2.5.3 The Wakeup Interrupt Controller
The Wakeup Interrupt Controller (WIC) is a peripheral that can detect an interrupt and wake the
processor from deep sleep mode. The WIC is enabled only when the DEEPSLEEP bit in the SCR is
set to 1, see Section 4.3.7 (p. 100) .
The WIC is not programmable, and does not have any registers or user interface. It operates entirely
from hardware signals.
When the WIC is enabled and the processor enters deep sleep mode, the power management unit
in the system can power down most of the Cortex-M3 processor. This has the side effect of stopping
the SysTick timer. When the WIC receives an interrupt, it takes a number of clock cycles to wakeup
the processor and restore its state, before it can process the interrupt. This means interrupt latency is
increased in deep sleep mode.
Note
相關PDF資料 |
PDF描述 |
|---|---|
| 1267 X 6" | TAPE ALUMINUM FOIL 6" X 1FT |
| 7810 0.25MM | ECAP COND PAD .25MM 7.7" X 10" |
| 7810 0.20MM | ECAP COND PAD .20MM 7.7" X 10" |
| 1170 X 6" | TAPE FOIL .002" 6" X 18YDS |
| EFM32-TG110F32-SK | IC MICRO KIT GECKO 24QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EFM32TG210F32-T | 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 32KB FLASH 32QFN |
| EFM32TG210F8 | 功能描述:ARM微控制器 - MCU 8KB Flash 2KB RAM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| EFM32TG210F8-QFN32 | 制造商:Energy Micro AS 功能描述:TINY GECKO MCU - Tape and Reel 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 8KB FLASH 32QFN |
| EFM32TG210F8-QFN32T | 制造商:Energy Micro AS 功能描述:32 BIT ARM MPU, TINY GECKO - Trays |
| EFM32TG210F8-QFN32-T | 制造商:Energy Micro AS 功能描述:IC MCU 32BIT 8KB FLASH 32QFN |
發布緊急采購，3分鐘左右您將得到回復。