- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5018BMTCX (FAIRCHILD SEMICONDUCTOR CORP) 6-Bit VID Controller 2-4 Phase VR10.X Controller PDF資料下載
參數資料
| 型號： | FAN5018BMTCX |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| 中文描述： | SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | LEAD FREE, MO-153AB, TSSOP-28 |
| 文件頁數： | 17/30頁 |
| 文件大小： | 509K |
| 代理商： | FAN5018BMTCX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
PRODUCT SPECIFICATION
FAN501
8
B
REV. 1.0.0 Jul/15/05
17
After the limit is reached, the 3V pull-up on the DELAY pin
is disconnected, and the external delay capacitor is dis-
charged through the external resistor. A comparator monitors
the DELAY voltage and shuts off the controller when the
voltage drops below 1.8V. Therefore, the RC time constant
discharging from 3V to 1.8V sets the current limit latch off
delay time. The Application Information section discusses
the selection of C
DLY
and R
DLY
.
Because the controller continues to cycle the phases during
the latch-off delay time, if the short is removed before the
1.8V threshold is reached, the controller will return to nor-
mal operation. The recovery characteristic depends on the
state of PWRGD. If the output voltage is within the PWRGD
window, the controller resumes normal operation. However,
if a short circuit has caused the output voltage to drop below
the PWRGD threshold, then a soft-start cycle is initiated.
The latch-off function can be reset by either cycling VCC to
the FAN5018B, or by cycling the Enable pin low for a short
time. To disable the short circuit latch off function, the
external resistor to ground should be left open, and a 1M
Ω
resistor should be connected from VCC to the DELAY pin.
This prevents the DELAY capacitor from discharging, so the
1.8V threshold is never reached. The resistor will have an
impact on the soft-start time because the current through it
will add to the internal 20μA current source.
During start-up when the output voltage is below 200mV, a
secondary current limit is active. This is necessary because
the voltage swing of CSCOMP cannot go below ground.
This secondary current limit controls the internal COMP
voltage to the PWM comparators to 2V. This will limit the
voltage drop across the low-side MOSFETs through the
current balance circuitry.
There is also an inherent per phase current limit that will pro-
tect individual phases if one or more phases stops function-
ing because of a faulty component. This
limit is based on the
maximum normal-mode COMP voltage.
Dynamic VID
The FAN5018B incorporates the ability to dynamically
change the VID input while the controller is running. This
allows the output voltage to change while the supply is run-
ning and supplying current to the load. This is commonly
referred to as VID-on-the-fly (OTF). A VID-OTF can occur
under either light load or heavy load conditions. The proces-
sor signals the controller by changing the VID inputs in mul-
tiple steps from the start code to the finish code. This change
can be either positive or negative.
When a VID input changes state, the FAN5018B detects the
change and ignores the DAC inputs for a minimum of 400ns.
This time is to prevent a false code due to logic skew while
the six VID inputs are changing. Additionally, the first VID
change initiates the PWRGD and CROWBAR blanking
functions for a minimum of 250μs to prevent a false
PWRGD or CROWBAR event. Each VID change will reset
the internal timer. Figure 4 shows the VID on-the-fly perfor-
mance when the output voltage is stepping up and the output
current is switching between minimum and maximum values
which is the worst-case situation.
Figure 4. VID On-the-Fly Waveforms, Circuit of Figure 5,
VID Change = 5mV, 5μs, 50 steps, I
OUT
Change = 5A to 65A
Figure 2. Start-Up Waveforms
Circuit of Figure 5Circuit of Figure 5
Channel 1 – Vout, Channel 2 – VccChannel 1 – Vcc, Channel 2 – Vout
Channel 3 – OD, Channel 4 – Delay pinChannel 3 – OD, Channel 4 – Delay pin
Figure 3. Overcurent Latch Off Waveform
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5019B | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019BMTCX | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019MTC | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019MTCX | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019 | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5019 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019_ABC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019_ABC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019_BBC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5019B | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:6-Bit VID Controller 2-4 Phase VR10.X Controller |
發布緊急采購，3分鐘左右您將得到回復。