- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5231 (FAIRCHILD SEMICONDUCTOR CORP) Micropower 5V, 100mA Low Dropout Linear Regulator PDF資料下載
參數資料
| 型號： | FAN5231 |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Micropower 5V, 100mA Low Dropout Linear Regulator |
| 中文描述： | 1 A SWITCHING REGULATOR, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | QSOP-28 |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 360K |
| 代理商： | FAN5231 |
FAN5231
6
REV. 1.1.1 8/15/01
Functional Pin Description
VID0, VID1, VID2, VID3, VID4 (Pins 11, 10, 9, 8
and 7 respectively)
VID0-VID4 are the input pins to the 5-bit DAC. The states of
these five pins program the internal voltage reference
(DACOUT). The level of DACOUT sets the core converter
output voltage (V
OUT1
). It also sets the core PGOOD, UVP
and OVP thresholds.
BOOT1, BOOT2 (Pins 25 and 3)
These pins provide power to the upper MOSFET drivers of
the core and I/O converters. Connect these pins to their
respective junctions of the bootstrap capacitors and the cath-
odes of the bootstrap diodes. The anodes of the bootstrap
diodes are connected to pin 28, VCC.
PHASE1, PHASE2 (Pins 23 and 5)
The PHASE nodes are the junction points of the upper MOS-
FET sources, output filter inductors, and lower MOSFET
drains. Connect the PHASE pins to the respective PWM con-
verter’s upper MOSFET source.
ISEN1, ISEN2 (Pins 22 and 6)
These pins are used to monitor the voltage drop across the
lower MOSFETs for current feedback, output voltage droop
and over-current protection. For precise current detection
these inputs could be connected to optional current sense
resistors placed in series with sources of the lower MOS-
FETs. To set the gain of the current sense amplifier, a resistor
should be placed in series with each of these inputs.
UGATE1, UGATE2 (Pins 24 and 4)
These pins provide the gate drive for the upper MOSFETs.
LGATE1, LGATE 2 (Pin 27 and 1)
These pins provide the gate drive for the lower MOSFETs.
PGND1, PGND2 (Pin 26 and 2)
These are the power ground connection for the core and I/O
converters, respectively. Tie each lower MOSFET source to
the corresponding pin.
VSEN2 (Pin 12)
This pin is connected to the I/O output and provides voltage
feedback to the I/O error amplifier. The PGOOD, UVP and
OVP comparators use this signal.
V3IN (Pin 13)
This pin provides input power for the 2.5V linear regulator.
The typical input voltage for that pin is 3.3V. Alternatively,
5.0V system rail can be used while efficiency will be propor-
tionally lower.
VOUT3 (Pin 14)
Output of the 2.5V linear regulator. Supplies current up to
150mA. The output current on this pin is internally limited to
250mA.
VSEN1, VRTN1 (Pins 17 and 16)
These pins are connected to the core converter’s output volt-
age to provide remote sensing. The PGOOD, UVP and OVP
comparators use this pins for protection.
SOFT (Pin 18)
Connect a capacitor from this pin to the ground. This capaci-
tor (typically 0.1mF), along with an internal 25μA current
source, sets the soft-start interval of the converter. When
voltage on this pin exceeds 0.9V, the soft start is completed.
After the soft-start is completed, the pin function is changed.
The internal circuit regulates voltage on this pin to the value
commanded by VID code. The pin now has 500μA source/
sink capability that allows to set desired slew rate for upward
and downward VID code changes.
VIN (Pin 19)
VIN provides battery voltage to the oscillator for feed-for-
ward rejection of input voltage variations.
EN (Pin 20)
This pin enables IC operation when left open or pulled-up to
VCC. Also, it unlatches the chip after fault when being
cycled.
PGOOD (Pin 21)
PGOOD is an open drain output used to indicate the status of
the PWM converters’ output voltages. This pin is pulled low
when the core output is not within ±10% of the DACOUT
reference voltage, or when any of the other outputs are not
within their respective under-voltage and over-voltage
thresholds.
The PGOOD output is pulled low for “01111” and ‘11111’
VID code. See Table 1.
GND (Pin 15)
Signal ground for the IC. All voltage levels are measured
with respect to this pin.
VCC (Pin 28)
Supplies all the power necessary to operate the chip. The IC
starts to operate when the voltage on this pin exceeds 4.5V
and shuts down when the voltage on this pin drops below
4.0V.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5231QSC | Analog IC |
| FAN5232 | Adjustable PWM Buck Controller for LCD PCs |
| FAN5232MTC | SMPS Controller |
| FAN5233 | System Electronics Regulator for Mobile PCs |
| FAN5233MTC | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5231 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5231QSC | 功能描述:開關變換器、穩壓器與控制器 QSOP-28 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5231QSCX | 功能描述:開關變換器、穩壓器與控制器 QSOP-28 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5232 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Adjustable PWM Buck Controller for LCD PCs |
| FAN5232_CBC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。