- 您現在的位置：買賣IC網 > PDF目錄375853 > FM75MM8X (Fairchild Semiconductor Corporation) Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm PDF資料下載
參數資料
| 型號： | FM75MM8X |
| 廠商： | Fairchild Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm |
| 中文描述： | 低電壓2 - Wire數字溫度傳感器，熱報警器 |
| 文件頁數： | 10/15頁 |
| 文件大小： | 532K |
| 代理商： | FM75MM8X |
FM75
PRODUCT SPECIFICATION
10
REV. 1.0.5 10/2/03
Serial Data Bus Operation
General Operation
Writing to and reading from the FM75 registers is accom-
plished via the SMBus-compatible two-wire serial interface.
SMBus protocol requires that one device on the bus initiates
and controls all read and write operations. This device is
called the “master” device. The master device also generates
the SCL signal which is the clock signal for all other devices
on the bus. All other devices on the bus are called “slave”
devices. The FM75 is a slave device. Both the master and
slave devices can send and receive data on the bus.
During SMBus operations, one data bit is transmitted per
clock cycle. All SMBus operations follow a repeating nine
clock-cycle pattern that consists of eight bits (one byte) of
transmitted data followed by an acknowledge (ACK) or not
acknowledge (NACK) from the receiving device. Note that
there are no unused clock cycles during any operation—
therefore there must be no breaks in the stream of data and
ACKs/NACKs during data transfers. Conversely having too
few clock cycles can lead to incorrect operation if an
inadvertent 8-bit read from a 16-bit register occurs.
For most operations, SMBus protocol requires the SDA line
to remain stable (unmoving) whenever SCL is high—i.e.,
transitions on the SDA line can only occur when SCL is low.
The exceptions to this rule are when the master device issues
a start or stop signal. Note that the slave device cannot issue
a start or stop condition.
The following are definitions for some general SMBus
terms:
Start Condition:
This condition occurs when the SDA line
transitions from high to low while SCL is high. The master
device uses this condition to indicate that a data transfer is
about to begin.
Stop Condition:
This condition occurs when the SDA line
transitions from low to high while SCL is high. The master
device uses this condition to signal the end of a data transfer.
Acknowledge
and
Not Acknowledge:
When data is trans-
ferred to the slave device it sends an acknowledge (ACK)
after receiving every byte of data. A master device sends an
acknowledge (ACK) following only the first byte read from a
2-byte register. The receiving device sends an ACK by
pulling SDA low for one clock. Following the last byte,
a master device sends a “not acknowledge” (NACK)
followed by a stop condition. A NACK is indicated by
leaving SDA high during the clock after the last byte.
Slave Address
Each slave device on the bus has a unique 7-bit address so
the master can identify which device is being read from or
written to.
The FM75 address is as follows:
The four MSBs of the FM75 address are hardwired to 1001.
The three LSBs are user configurable by tying the A0, A1
and A2 pins to either V
D
D or ground. This provides eight
different FM75 addresses, which allows up to eight FM75s
to be connected to the same bus.
Writing To and Reading From the FM75
All read and write operations must begin with a start signal
generated by the master device. After the start condition, the
master device must immediately send a slave address (7 bits)
followed by a read/write bit. If the slave address matches the
address of the FM75, the FM75 sends an ACK after
receiving the read/write bit by pulling the SDA line low
for one clock. See Figure 8 through Figure 13 for timing
diagrams for all FM75 operations.
Setting the Pointer
For all operations the pointer stored in the Command
Register must be pointing to the register (Temperature,
Configuration, T
OS
or T
HYST
) that is going to be written to
or read from. To change the pointer value in the Command
Register, the read/write bit following the address must be 0.
This indicates that the master will now write new informa-
tion into the Command Register.
After the FM75 sends an ACK in response to receiving the
address and read/write bit, the master device must transmit
an appropriate 8-bit pointer value as explained in the
Registers section of this data sheet. The FM75 will send an
ACK after receiving the new pointer data.
The pointer set operation is illustrated in Figure 8. Anytime a
pointer set is performed, it must be immediately followed by
a read or write operation. Note that the 6 MSBs of the
pointer value must be zero. If the 6 MSBs are not zero, the
FM75 will not send an ACK and will internally terminate the
operation. Also recall that the Command Register retains the
current pointer value between operations. Therefore, once a
register is being pointed to, subsequent read operations do
not require a pointer set cycle. Write operations always
require the pointer be reset.
1
0
0
1
A1
A2
A0
相關PDF資料 |
PDF描述 |
|---|---|
| FM75 | Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm |
| FM75M8X | Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm |
| FM803MS3X | 3-Pin レC Supervisor Device |
| FM803RP3X | 3-Pin レC Supervisor Device |
| FM803SP3X | 3-Pin レC Supervisor Device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM7C4 | 制造商:BACO Controls Inc 功能描述: |
| FM7Q1/25/W | 制造商:Quam-Nichols Manufacturing 功能描述:6-1/2" O.D. LF speaker /1" HF, 2-way with multiple position "U" bracket, 20W-25V |
| FM7Q1/8/W | 制造商:Quam-Nichols Manufacturing 功能描述:6-1/2" O.D. LF speaker /1" HF, 2-way with multiple position "U" bracket, 30W, 8 |
| FM7W2P1-K120 | 功能描述:D-Sub混合觸點連接器 7 POS PCB PLUG 7W2 5 PIN 2 HOLE RoHS:否 制造商:FCI 觸點布置: 位置/觸點數量: 安裝風格:Through Hole 安裝角: 端接類型:Solder |
| FM7W2P5-1002 | 功能描述:D-Sub混合觸點連接器 7 POS R/A PCB PLUG 7W2 5 PIN 2 HOLE RoHS:否 制造商:FCI 觸點布置: 位置/觸點數量: 安裝風格:Through Hole 安裝角: 端接類型:Solder |
發布緊急采購，3分鐘左右您將得到回復。