- 您現在的位置：買賣IC網 > PDF目錄375853 > FM75MM8X (Fairchild Semiconductor Corporation) Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm PDF資料下載
參數資料
| 型號： | FM75MM8X |
| 廠商： | Fairchild Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm |
| 中文描述： | 低電壓2 - Wire數字溫度傳感器，熱報警器 |
| 文件頁數： | 6/15頁 |
| 文件大小： | 532K |
| 代理商： | FM75MM8X |
FM75
PRODUCT SPECIFICATION
6
REV. 1.0.5 10/2/03
Comparator Mode
In Comparator Mode, each time a temperature-to-digital
(T-to-D) temperature conversion occurs, the new digital tem-
perature is compared to the value stored in the T
T
HYST
registers. If a fault tolerance number of consecutive
temperature measurements are greater than the value stored
in the T
OS
register, the O.S. output will be activated.
For example, if bits F1 and F0 are equal to “10” (fault
tolerance = 4), four consecutive temperature measurements
must exceed T
OS
to activate the O.S. output. Once the O.S
output is active, it will remain active until the first time the
measured temperature drops below the temperature stored in
the T
HYST
register. The operation of the alarm in Comparator
Mode with fault tolerance=2 is illustrated in Figure 1.
OS
and
Interrupt Mode
In Interrupt Mode the O.S. output will first become active
after a fault tolerance number of consecutive temperature
measurements exceed the value stored in the T
(similar to Comparator Mode). Once O.S. is active, it can
only be cleared by a user read from any of the FM75
registers (Temperature, Configuration, T
putting the FM75 into Shutdown Mode (i.e., by setting the
shutdown bit in the Configuration Register to “1”). Once
cleared, the O.S. output can only be activated the next time
by a fault tolerance number of consecutive temperature
measurements that are lower than the value stored in T
Again, once it is activated the O.S. output can only be
deactivated by a user read or shutdown. Thus, in Interrupt
Mode the activate/clear cycle for O.S. has the following
pattern: temperature > T
OS
, clear, temperature < T
clear, temperature > T
OS
, clear, etc. The operation of the
alarm in Interrupt Mode with fault tolerance=2 is also
illustrated in Figure 1.
OS
register
OS
, or T
HYST
) or by
HYST
.
HYST
,
Figure 1. Thermal Alarm Operation in Comparator and Interrupt Modes
For this example:
Fault Tolerance = 2
Output Polarity = Active Low
Read (or Shutdown)
T
OS
T
HYST
Temperature-to-Digital
Conversion
O.S. (Comparator Mode)
O.S. (Interrupt Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| FM75 | Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm |
| FM75M8X | Low Voltage 2-Wire Digital Temperature Sensor with Thermal Alarm |
| FM803MS3X | 3-Pin レC Supervisor Device |
| FM803RP3X | 3-Pin レC Supervisor Device |
| FM803SP3X | 3-Pin レC Supervisor Device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM7C4 | 制造商:BACO Controls Inc 功能描述: |
| FM7Q1/25/W | 制造商:Quam-Nichols Manufacturing 功能描述:6-1/2" O.D. LF speaker /1" HF, 2-way with multiple position "U" bracket, 20W-25V |
| FM7Q1/8/W | 制造商:Quam-Nichols Manufacturing 功能描述:6-1/2" O.D. LF speaker /1" HF, 2-way with multiple position "U" bracket, 30W, 8 |
| FM7W2P1-K120 | 功能描述:D-Sub混合觸點連接器 7 POS PCB PLUG 7W2 5 PIN 2 HOLE RoHS:否 制造商:FCI 觸點布置: 位置/觸點數量: 安裝風格:Through Hole 安裝角: 端接類型:Solder |
| FM7W2P5-1002 | 功能描述:D-Sub混合觸點連接器 7 POS R/A PCB PLUG 7W2 5 PIN 2 HOLE RoHS:否 制造商:FCI 觸點布置: 位置/觸點數量: 安裝風格:Through Hole 安裝角: 端接類型:Solder |
發布緊急采購，3分鐘左右您將得到回復。