- 您現在的位置：買賣IC網 > PDF目錄375864 > FMS7401LEN14 (FAIRCHILD SEMICONDUCTOR CORP) Digital Power Controller PDF資料下載
參數資料
| 型號： | FMS7401LEN14 |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Digital Power Controller |
| 中文描述： | 8-BIT, EEPROM, 2.04 MHz, MICROCONTROLLER, PDIP14 |
| 封裝： | PLASTIC, DIP-14 |
| 文件頁數： | 30/80頁 |
| 文件大小： | 1535K |
| 代理商： | FMS7401LEN14 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
FMS7401/7401L
PRODUCT SPECIFICATION
30
REV. 1.0.2 6/23/04
5.3
The Programmable Comparator’s output (C
OUT
) is fed into the digital delay filter with a programmable delay time. The C
OUT
signal toggles from 0 to 1 when the external input (G4/AIN0 or G2/AIN2) voltage is higher than the programmed voltage
threshold or Uncommitted Amplifier output (A
OUT
), depending on the state of VLOOP. The C
OUT
rising edge transition triggers
the programmable digital delay counter to begin incrementing. With each digital delay count, its value is compared against the
value stored in the DD[3:0] bits of the Digital Delay (DDELAY) control register. If C
OUT
remains high when the digital delay
count equaling DD[3:0] completes, the PWMOFF signal transitions from 0 to 1. This rising edge transition of the PWMOFF
signal is then used to either disable the PWM Timer 1 circuit completely or the current PWM cycle forcing the PWM output
signals to their resting (off) state. The PWMOFF output signal may also be programmed as an input of the G6 port MIW
circuit. Interrupts may be triggered if the G6 port MIW circuit is enabled and configured to trigger its microcontroller hardware
interrupt (EDGEI). Refer to the
Multi-input Wakeup Circuit
section of the datasheet regarding for configuration details.
Digital Delay Filter with PWMOFF Output
Bit 7 of the DDELAY register is the Programmable Comparator circuit enable (COMPEN) bit. If COMPEN=0, the Program-
mable Comparator circuit is disabled and the C
OUT
signal is low. If COMPEN=1, the Programmable Comparator circuit is
enabled and the C
OUT
signal is generated by the comparison of the two inputs.
Bit 6 (PWMINT) of the DDELAY register, if set to 1, selects the PWMOFF signal in place of its G6 input to the MIW circuit.
Software must then enable the MIW PWMOFF/G6 circuit by setting the WKEN[6] bit. The WKEDG[6] bit must also be
cleared to select the rising edge transitions on the PWMOFF signal as its WKPND[6] bit trigger. Software may monitor the
WKPND[6] flag or enable the MIW hardware interrupt (EDGEI) to help detect when the PWMOFF signal is triggered.
3
Bit 5 (EPWM) of the DDELAY register is the digital delay filter and PWMOFF signal enable bit. The EPWM bit is active low
so that on power-up (after a system reset) the digital delay filter circuit is automatically enabled once the Programmable
Comparator circuit is enabled. If the Programmable Comparator and PWM Timer 1 circuits are enabled, since the filter is
defaulted enabled, the PWMOFF signal may disable the PWM Timer 1 upon a comparator transition. If the digital delay filter
and PWMOFF circuit is not needed, software must set the EPWM bit to 1 disabling the filter before enabling the Programma-
ble Comparator to prevent unwanted disables of the PWM Timer 1 circuit or its outputs.
Bit 4 (OFFMODE) of the DDELAY register determines how the PWMOFF signal affects the PWM Timer 1 circuit. If OFF-
MODE=0 and the Timer 1 circuit is configured in an enabled PWM Mode, Timer 1 is automatically disabled forcing the PWM
T1HS1 and T1HS2 output signals to their resting (off) states with the rising edge of the PWMOFF signal. The T1C0 bit of the
T1CNTRL2 register is cleared, reinitializing the 12-bit TMR1 counter to 0x000. Software must re-enable the Timer 1 circuit to
reactivate the PWM output signals. If OFFMODE=1 and Timer 1 is configured in PWM Mode, the T1HS1 and T1HS2 output
signals are forced to their resting (off) state until the current PWM cycle completes. Once the PWM cycle completes, the
PWMOFF signal releases the T1HS1 and T1HS2 output signals and they resume with their normal operation even if the C
OUT
signal remains active (1). The next PWMOFF trigger will not occur until the next rising edge of C
OUT
.
Bits 3-0 (DD[3:0]) of the DDELAY register determine how long to delay the trigger of the PWMOFF signal once the rising
edge of C
OUT
has been detected. Once the digital delay counter is triggered, the delay count is compared against the value
stored in the DD[3:0] bits. Once the delay counter completes its DD[3:0] count, if C
OUT
remains high, the PWMOFF signal is
triggered. The digital delay counters increment at the device reference clock rate (F
RCLK2
).
4
相關PDF資料 |
PDF描述 |
|---|---|
| FMS7401LVN | Digital Power Controller |
| FMS7401LVN14 | Digital Power Controller |
| FMS7G10US60S | SWTCH ROLLER SPDT 20A SCRW TERM |
| FMS7G10US60 | SWTCH ROLLER SPDT 20A SOLD TERM |
| FMS7G15US60S | SWTCH LEVER SPDT 20A SCREW TERM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FMS7401LEN14_Q | 功能描述:處理器 - 專門應用 Int Controller for Ballast RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432 |
| FMS7401LVN | 功能描述:處理器 - 專門應用 Int Controller for Ballast RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432 |
| FMS7401LVN14 | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS7401LVN14_Q | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS75X6 | 功能描述:MAGENTIC STRIP .75" X 6' RoHS:否 類別:線纜，導線 - 管理 >> 線槽，走線系統 - 附件 系列:- 標準包裝:1 系列:PANDUCT® 附件類型:蓋 - 線管 適用于相關產品:Panduit 導管 H 型 高度:- 寬:4"（101.6mm） 長度:36.0"（914.4mm） 顏色:黑 其它名稱:298-HC4BL36 |
發布緊急采購，3分鐘左右您將得到回復。