- 您現在的位置：買賣IC網 > PDF目錄375864 > FMS7401LVN (FAIRCHILD SEMICONDUCTOR CORP) Digital Power Controller PDF資料下載
參數資料
| 型號： | FMS7401LVN |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Digital Power Controller |
| 中文描述： | 8-BIT, EEPROM, 2.04 MHz, MICROCONTROLLER, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 18/80頁 |
| 文件大小： | 1535K |
| 代理商： | FMS7401LVN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
FMS7401/7401L
PRODUCT SPECIFICATION
18
REV. 1.0.2 6/23/04
Bit 6 of the ADCNTRL1 register is the ADC’s microcontroller hardware interrupt enabled (AINTEN) bit. If set, hardware
interrupts (ADCI) are enabled and triggered by the APND pending flag.
5
As long as the ADC pending flag is set, the hardware
interrupt will continue to execute software’s ADC interrupt service routine until the pending flag is cleared.
6
Bit 5 of the ADCNTRL1 register is the ADC Conversion Start/Busy (ASTART) bit. Software must set the ASTART bit to ini-
tiate an ADC conversion when the ENDAS bit of the ADCNTRL2 register is set to 0. The ASTART bit will remain high as long
as an ADC conversion is in progress (whether software or the ADSTROBE signal triggered the conversion). If software
attempts to clear the ASTART bit while a conversion is in progress, the write command is ignored and the ASTART bit remains
high until the conversion cycle completes. Software should monitor ASTART to determine when the conversion has completed
instead of the APND bit. The APND bit may be triggered before the ASTART is automatically cleared. The ADC conversion
completion delay may occur when the F
ICLK
clock is slower than an ADC conversion clock cycle.
Bit 4 of the ADCNTRL1 register is the ADC Voltage Reference Selection (REFSEL) bit. If REFSEL=0, the ADC Reference
Voltage (V
AREF
) becomes sourced by the internal bandgap voltage reference (V
REF
). If REFSEL=1, the ADC Reference Voltage
(V
AREF
) becomes sourced by Vcc. If the ADC circuit is performing a conversion, software must avoid writing to the REFSEL
bit.
Bits 3-0 of the ADCNTRL1 register are the Analog Channel Selection (ACHSEL[3:0]) bits selecting one of the eight analog
input channels to convert its voltage (see
Table 6
). Software may write to the ACHSEL bits at any time; however, the actual
ACHSEL selection signals will not change while an ADC conversion is in progress. If a read command is issued while a con-
version is in progress, the current value of the ACHSEL bits may not necessarily reflect the actual state of the ACHSEL selec-
tion signals. The last value of the ACHSEL bits written by software at the time of the ADC conversion trigger, dictates the state
of the ACHSEL selection signals for the triggered ADC conversion cycle.
The SBIT or RBIT instructions may be used to either set or clear one of the ADCNTRL1 register bits, like the AINTEN bit.
The SBIT and RBIT instructions both take two instruction clock cycles to complete their execution. In the first cycle, all regis-
ter bits are automatically read to obtain their most current value. In the second cycle, the bit to be set/cleared is given its new
value and all bits are then re-written to the register. Using the SBIT/RBIT instruction to set/clear an enable bit with a pending
flag in the same register may cause a potential hazard. Software may inadvertently clear a recently triggered pending flag if the
trigger happened during the second phase of the SBIT/RBIT instruction execution. To avoid this condition, the LD instruction
must be used to set or clear the interrupt enable bit. The ADC circuit is designed such that software may not trigger a pending
flag by writing a 1 to the APND bit, it may only be cleared. The action of writing a 1 to the APND register bit holds its current
bit value. The action of writing a 0 to the APND register bit clears the bit value. Therefore, the “LD T1CNTRL, #0E0H”
instruction will set the ASTART and AINTEN bits without clearing APND.
相關PDF資料 |
PDF描述 |
|---|---|
| FMS7401LVN14 | Digital Power Controller |
| FMS7G10US60S | SWTCH ROLLER SPDT 20A SCRW TERM |
| FMS7G10US60 | SWTCH ROLLER SPDT 20A SOLD TERM |
| FMS7G15US60S | SWTCH LEVER SPDT 20A SCREW TERM |
| FMS7G15US60 | SWTCH ROLLER SPDT 20A SCRW TERM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FMS7401LVN14 | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS7401LVN14_Q | 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| FMS75X6 | 功能描述:MAGENTIC STRIP .75" X 6' RoHS:否 類別:線纜，導線 - 管理 >> 線槽，走線系統 - 附件 系列:- 標準包裝:1 系列:PANDUCT® 附件類型:蓋 - 線管 適用于相關產品:Panduit 導管 H 型 高度:- 寬:4"（101.6mm） 長度:36.0"（914.4mm） 顏色:黑 其它名稱:298-HC4BL36 |
| FMS7857MTD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver |
| FMS7857MTDT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver |
發布緊急采購，3分鐘左右您將得到回復。