欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: FMS7401LVN
廠商: FAIRCHILD SEMICONDUCTOR CORP
元件分類: 微控制器/微處理器
英文描述: Digital Power Controller
中文描述: 8-BIT, EEPROM, 2.04 MHz, MICROCONTROLLER, PDIP8
封裝: PLASTIC, DIP-8
文件頁數: 49/80頁
文件大小: 1535K
代理商: FMS7401LVN
PRODUCT SPECIFICATION
FMS7401/7401L
REV. 1.0.2 6/23/04
49
Carry/Borrow (C)
The carry flag is set if the arithmetic logic unit (ALU) performs a carry or borrows during an arithmetic operation and by its
special inherent instructions—set carry (SC), load carry (LDC) and invert carry (INVC). The rotate instructions—rotate right/
left through carry (RRC/RLC)—operate with and through the carry bit to facilitate multiple-word shift operations. The RC,
SC, INVC, LDC and STC (store carry) instructions facilitate direct bit manipulation using the carry flag.
Half Carry (H)
The half carry flag indicates whether an overflow has taken place on the boundary between the two nibbles in the accumulator.
It is primarily used for Binary Coded Decimal (BCD) arithmetic calculation. The RC and SC instructions facilitate direct bit
manipulation of the half carry flag.
Zero (Z)
The zero flag is set if the result of an arithmetic, logic, or data manipulation operation is zero. Otherwise, the zero flag is
cleared.
Negative (N)
The result from an arithmetic, logic, or data manipulation operation is negative if the MSB is one, therefore setting the negative
flag. Otherwise, the negative flag is cleared.
Global Interrupt Mask (G)
The global interrupt bit (G) is a global mask that disables all maskable interrupt sources. If G is cleared, interrupts can become
pending but the operation of the core continues uninterrupted (even if the individual interrupts are enabled). However, if G is
set when an interrupt becomes pending the core will be interrupted and execute the appropriate interrupt service routine.
After a reset, G is defaulted to zero and can only be set by a software instruction. When an interrupt is recognized, G is auto-
matically cleared after the program counter value is stacked and the interrupt vector addressing the interrupt service routine is
fetched. Once the interrupt is serviced, a return-from-interrupt (RETI) instruction is normally executed to restore the program
counter to the value before the interrupt occurred. G is the restored to one after the return from interrupt is executed. Although
G can be set within an interrupt service routine, “nesting” interrupts in this way should only be done when there is a clear
understanding of latency and of the arbitration mechanism.
Table 23. Interrupt Priority Sequence
Priority (5 highest, 1 lowest)
Interrupt
5
Software
(INTR)
4
MIW
(EDGEI)
3
Timer 0
(TMRI0)
2
PWM Timer 1
(TMRI1)
1
ADC
(ADCI)
相關PDF資料
PDF描述
FMS7401LVN14 Digital Power Controller
FMS7G10US60S SWTCH ROLLER SPDT 20A SCRW TERM
FMS7G10US60 SWTCH ROLLER SPDT 20A SOLD TERM
FMS7G15US60S SWTCH LEVER SPDT 20A SCREW TERM
FMS7G15US60 SWTCH ROLLER SPDT 20A SCRW TERM
相關代理商/技術參數
參數描述
FMS7401LVN14 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
FMS7401LVN14_Q 功能描述:8位微控制器 -MCU Int Controller for Ballast RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
FMS75X6 功能描述:MAGENTIC STRIP .75" X 6' RoHS:否 類別:線纜,導線 - 管理 >> 線槽,走線系統 - 附件 系列:- 標準包裝:1 系列:PANDUCT® 附件類型:蓋 - 線管 適用于相關產品:Panduit 導管 H 型 高度:- 寬:4"(101.6mm) 長度:36.0"(914.4mm) 顏色:黑 其它名稱:298-HC4BL36
FMS7857MTD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver
FMS7857MTDT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Ten Distributed-Output Clock Driver
主站蜘蛛池模板: 浮山县| 潢川县| 大余县| 庄浪县| 平阴县| 儋州市| 孝感市| 开封市| 岗巴县| 南郑县| 叙永县| 长顺县| 伊宁县| 牡丹江市| 白山市| 政和县| 夹江县| 云南省| 全州县| 古浪县| 旺苍县| 天水市| 葫芦岛市| 晋江市| 财经| 赤城县| 郁南县| 沛县| 湟中县| 镇赉县| 桂阳县| 双牌县| 昭觉县| 延边| 丹东市| 南木林县| 乌拉特后旗| 新宁县| 峨边| 桂林市| 建昌县|