欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: GS881E36AD-166I
廠商: GSI TECHNOLOGY
元件分類: DRAM
英文描述: 512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
中文描述: 256K X 36 CACHE SRAM, 7 ns, PBGA165
封裝: 13 X 15 MM, 1 MM PITCH, FBGA-165
文件頁數: 28/37頁
文件大小: 662K
代理商: GS881E36AD-166I
GS881E18/36AT-250/225/200/166/150/133
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.03 11/2004
20/29
2001, GSI Technology
JTAG Port Registers
Overview
The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s
and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the
rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the
TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or
the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the
TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the
controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through
the RAM’s JTAG Port to another device in the scan chain with as little delay as possible.
Boundary Scan Register
The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM’s input or I/O pins.
The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port’s TDO pin. The
Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the
device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan
Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in
Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z,
SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register.
JTAG Pin Descriptions
Pin
Pin Name
I/O
Description
TCK
Test Clock
In
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate
from the falling edge of TCK.
The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP
controller state machine. An undriven TMS input will produce the same result as a logic one input
level.
The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers
placed between TDI and TDO. The register placed between TDI and TDO is determined by the
state of the TAP Controller state machine and the instruction that is currently loaded in the TAP
Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce
the same result as a logic one input level.
Output that is active depending on the state of the TAP state machine. Output changes in
response to the falling edge of TCK. This is the output side of the serial registers placed between
TDI and TDO.
TMS
Test Mode Select
In
TDI
Test Data In
In
TDO
Test Data Out
Out
Note:
This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is
held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
相關PDF資料
PDF描述
GS881E36AD-166IT 512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-166T 512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-200 512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-200I 512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-200IT 512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
相關代理商/技術參數
參數描述
GS881E36AD-166IT 制造商:GSI 制造商全稱:GSI Technology 功能描述:512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-166T 制造商:GSI 制造商全稱:GSI Technology 功能描述:512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-200 制造商:GSI 制造商全稱:GSI Technology 功能描述:512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-200I 制造商:GSI 制造商全稱:GSI Technology 功能描述:512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
GS881E36AD-200IT 制造商:GSI 制造商全稱:GSI Technology 功能描述:512K x 18, 256K x 36 9Mb Synchronous Burst SRAMs
主站蜘蛛池模板: 安平县| 张家港市| 奇台县| 望奎县| 科技| 东辽县| 句容市| 利津县| 信丰县| 缙云县| 富蕴县| 理塘县| 伊金霍洛旗| 繁峙县| 江油市| 涿鹿县| 荣昌县| 成安县| 徐汇区| 武胜县| 阜康市| 兰坪| 渑池县| 汝城县| 万源市| 平乐县| 萨迦县| 宝鸡市| 于田县| 灵台县| 梓潼县| 汕头市| 许昌县| 青阳县| 阿鲁科尔沁旗| 新密市| 阿克苏市| 金堂县| 遂川县| 瑞丽市| 方正县|