欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HT48R50A
廠商: Holtek Semiconductor Inc.
元件分類: 數學處理器
英文描述: 8-BIT MICROCONTROLLER
中文描述: 8位微控制器
文件頁數: 14/46頁
文件大小: 1037K
代理商: HT48R50A
HT48R50A-1
Rev. 1.10
14
July 2, 2001
abled, the stack is not full and the T1F is set, a
subroutine call to location 0CH will occur. The
related interrupt request flag (T1F) will be re-
set and the EMI bit cleared to disable further
interrupts.
Duringtheexecutionofaninterruptsubroutine,
other interrupt acknowledge signals are held
until the "RETI" instruction is executed or the
EMI bit and the related interrupt control bit are
set to 1 (if the stack is not full). To return from
the interrupt subroutine, "RET" or "RETI" may
be invoked. RETI will set the EMI bit to enable
an interrupt service, but RET will not.
Interrupts, occurring in the interval between
the rising edges of two consecutive T2 pulses,
will be serviced on the latter of the two T2
pulses, if the corresponding interrupts are en-
abled. In the case of simultaneous requests the
following table shows the priority that is ap-
plied. These can be masked by resetting the
EMI bit.
No. Interrupt Source Priority Vector
a
External Interrupt
1
04H
b
Timer/event
counter 0 overflow
2
08H
c
Timer/event
counter 1 overflow
3
0CH
The Timer/Event Counter 0/1 interrupt request
flag (/T1F), external interrupt request flag
(EIF), enable Timer/Event Counter 0/1 inter-
rupt bit (ET0I/ET1I), enable external interrupt
bit (EEI) and enable master interrupt bit (EMI)
constitute an interrupt control register (INTC)
which is located at 0BH in the data memory.
EMI, EEI, ET0I and ET1I are used to control
the enabling/disabling of interrupts. These bits
prevent the requested interrupt from being ser-
viced. Once the interrupt request flags (T0F,
T1F, EIF) are set, they will remain in the INTC
register until the interrupts are serviced or
cleared by a software instruction.
It is recommended that a program does not
use the "CALL subroutine" within the inter-
rupt subroutine. Interrupts often occur in an
unpredictable manner or need to be serviced
immediately in some applications. If only one
stack is left and enabling the interrupt is not
well controlled,theoriginalcontrolsequencewill
be damaged once the "CALL" operates in the in-
terrupt subroutine.
Oscillator configuration
There are 3 oscillator circuits in the
microcontroller.
All of them are designed for system clocks,
namely the external RC oscillator, the external
Crystal oscillator and the internal RC
oscillator, which are determined by ROM code
option. No matter what oscillator type is se-
lected, the signal provides the system clock.
The HALT mode stops the system oscillator
and ignores an external signal to conserve
power.
& ! * < +
1 : = # ! * !
,
*
. : = # ! * !
1 : ! : *
,
* # : !
, - ,
'
" ! #
!
,
*
Watchdog Timer
& !* #
7 ' * 4 . 2 1 > @ 8
*
# !
* " * #
+
+ . " 6
System oscillator
相關PDF資料
PDF描述
HT48RA0A 8-Bit Remote Type MCU
HT48RA3 8-Bit Remote Type OTP MCU
HT48RB8 8-Bit USB Type OTP MCU
HT49C10 8-BIT MICROCONTROLLER
HT49C30L HDSP-A101 RED DISPLAY, LED,
相關代理商/技術參數
參數描述
HT48R50A-1 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type 8-Bit MCU
HT48R50A-1_09 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O Type 8-Bit MCU
HT48R51 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit Microcontroller Series
HT48R51-1(28SKDIP-H0) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
HT48R51-1(40DIP-A0) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
主站蜘蛛池模板: 若羌县| 博罗县| 曲阜市| 宜昌市| 临潭县| 华容县| 湘乡市| 岳西县| 达州市| 通河县| 石狮市| 文登市| 肇州县| 昔阳县| 故城县| 万荣县| 辽阳市| 融水| 琼海市| 邹平县| 犍为县| 潜江市| 满洲里市| 洛南县| 台中市| 黄梅县| 磐石市| 方正县| 柘城县| 宁乡县| 武穴市| 宾川县| 凌海市| 丘北县| 金湖县| 右玉县| 吉水县| 长治市| 巫溪县| 新和县| 深水埗区|