- 您現在的位置：買賣IC網 > PDF目錄385403 > HT82A851R (Holtek Semiconductor Inc.) USB Audio MCU PDF資料下載
參數資料
| 型號： | HT82A851R |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | USB Audio MCU |
| 中文描述： | USB音頻控制器 |
| 文件頁數： | 20/43頁 |
| 文件大小： | 304K |
| 代理商： | HT82A851R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
HT82A851R
Rev. 1.20
20
June 15, 2007
TheMISCregistercombinescommandandstatustocontrolthedesiredendpointFIFOactionandtoshowthestatusof
the desired endpoint FIFO. MISC will be cleared by a USB reset signal.
Bit No.
Label
R/W
Power-on
Functions
0
REQUEST
R/W
0
After setting the status of the desired one, FIFO can be requested
by setting this bit high . After finishing, this bit must be set low.
1
TX
R/W
0
To represent the direction and transition end MCU access. When
set to logic 1, the MCU desires to write data to the FIFO. After
finishing, this bit must be set to logic 0 before terminating request to
represent transition end. For an MCU read operation, this bit must
be set to logic 0 and set to logic 1 after finishing.
2
CLEAR
R/W
0
MCUrequeststocleartheFIFO,eveniftheFIFOisnotready.After
clearing the FIFO, the USB interface will send force_tx_err to tell
the Host that data under-run if the Host wants to read data.
3
ISO_IN_EN
R/W
0
Enables the isochronous in pipe interrupt.
4
ISO_OUT_EN
R/W
0
Enables the isochronous out pipe interrupt.
5
SETCMD
R/W
0
To show that the data in the FIFO is a setup command. This bit will
remain in this state until the next one enters the FIFO.
6
READY
R
0
To show that the desired FIFO is ready
7
LEN0
R
0
To show that the host sent a 0-sized packet to the MCU. This bit
must be cleared by a read action to the corresponding FIFO.
MISC (26H) Register
Bit No.
Label
R/W
Power-on
Functions
0
DATATG*
R/W
0
DATA token toggle bit
1
SETIO1**
R/W
1
Set endpoint1 input or output pipe (1/0), default input pipe(1)
2
SETIO2**
R/W
0
Set endpoint2 input or output pipe (1/0), default output pipe(0)
3
SETIO3**
R/W
1
Set endpoint3 input or output pipe (1/0), default input pipe(1)
4
SETIO4**
R/W
1
Set endpoint4 input or output pipe (1/0), default input pipe(1)
5~7
Undefined bit, read as 0
Note: *USB definition: when the host sends a set Configuration , the Data pipe should send the DATA0 (about the
Data toggle) first. So, when the Device receives a set configuration setup command, the user needs to toggle
this bit as the following data will send a Data0 first.
**It is only required to set the data pipe as an input pile or output pile. The purpose of this function is to avoid the
host sending a abnormal IN or OUT token and disabling the endpoint.
SETIO (27H) Register, USB Endpoint 1 ~ Endpoint 4 Set IN/OUT Pipe Register
The speaker output volume and speaker mute/un-mute are controlled by the USB Speaker Volume Control register.
The range of the volume is set from 6 dB to -32 dB by software.
Speaker mute control:
MUTE=0: Mute Speaker output
MUTE=1: Normal
Bit No.
Label
R/W
Power-on
Functions
0~6
USVC0~
USVC6
R/W
0
Volume control Bit0~Bit6
7
MUTE
R/W
0
Mute control, low active.
USB Speaker Volume Control (1CH) Register
相關PDF資料 |
PDF描述 |
|---|---|
| HT82J30A | 16 Channel A/D MCU with SPI Interface |
| HT82J30R | 16 Channel A/D MCU with SPI Interface |
| HT82J927A | USB Gamepad |
| HT82J97E | USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E-20SOP-A | USB Joystick Encoder 8-Bit OTP MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82B40A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface |
| HT82B40R | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface |
| HT82B40R_11 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface |
| HT82B42R | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface |
| HT82B42RE | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:I/O MCU with USB Interface |
發布緊急采購，3分鐘左右您將得到回復。