- 您現在的位置：買賣IC網 > PDF目錄385403 > HT82J30R (Holtek Semiconductor Inc.) 16 Channel A/D MCU with SPI Interface PDF資料下載
參數資料
| 型號： | HT82J30R |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 16 Channel A/D MCU with SPI Interface |
| 中文描述： | 16通道A / D轉換，SPI接口單片機 |
| 文件頁數： | 16/47頁 |
| 文件大小： | 312K |
| 代理商： | HT82J30R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
HT82J30R/HT82J30A
Rev. 1.00
16
December 20, 2006
write 1 . The input source also depends on the control
register. If the control register bit is 1 , the input will
read the pad state. If the control register bit is 0 , the
contents of the latches will move to the internal bus. The
latter is possible in the read-modify-write instruction.
For output function, all I/Os except PB2, PB3, PD2, PD7
are CMOS types. There are options to define PB2, PB3,
PD2, PD7 as either CMOS or NMOS types. These con-
trol registers are mapped to locations 13H, 15H,
17H,19H and 23H.
After a device reset, these input/output lines remain at
high levels or a floating state, depending upon the
pull-high configuration options. Each bit of these in-
put/output latches can be set or cleared using the SET
[m].i and CLR [m].i instructions.
Some instructions first input data and then follow the
output operations. For example,
SET [m].i ,
CLR
[m].i , CPL [m] , CPLA [m] read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Each line of port A has the capability of waking-up the
device.
Each I/O line has a pull-high option. Once a pull-high op-
tion is selected, the I/O line has a pull-high resistor
connected, otherwise, there are none. Take note that a
non-pull-high I/O line operating as an input will be in a
floating state.
Pin PA3 is pin-shared with the PFD signal. If the PFD
configuration option is selected, the output signal on
PA3, if setup as an output, will be the PFD signal gener-
ated by the timer/event counter overflow signal. If setup
as an input then the pin will retain its input function.
Once the PFD configuration option is selected, the PFD
output signal is controlled by the PA3 data register. Writ-
ing a 1 to the PA3 data register will enable the PFD
output function and writing 0 will force pin PA3 to re-
mainat 0 .TheI/OfunctionsofPA3are shownbelow.
I/O
Mode
I/P
(Normal)
O/P
(Normal)
I/P
(PFD)
O/P
(PFD)
PA3
Logical
Input
Logical
Output
Logical
Input
PFD
(Timer on)
Note:
The PFD frequency is the timer/event counter
overflow frequency divided by 2.
PA6, PA5 and PA4 are pin-shared with the INT0, INT1
and TMR pins respectively.
PB and PC can also be used as A/D converter inputs.
The A/D function will be described later. There are two
SPI interfaces which are shared with pins PD1~PD4,
PD7 and PF0~PF2. The SPI function will be described
later. There is a PWM function shared with pin PD0. If
the PWM function is enabled, the PWM signal will ap-
pear on pin PD0 (if PD0 is setup as an output). Writing a
1 to the PD0 data register will enable the PWM output
function and writing a 0 will force the PD0 to remain at
0 . The I/O functions of PD0 are shown in the table.
I/O
Mode
I/P
(Normal)
O/P
(Normal)
I/P
(PWM)
O/P
(PWM)
PD0
Logical
Input
Logical
Output
Logical
Input
PWM
It is recommended that unused or not bonded out I/O
.
;
, <
4
7 !
! "
*
/
2 %
*
2 %
% &
4
7 !
;
2 % <
'
" &
,
.
;
4
<
H
$
2 1 "
2 2 7 C " )
! "
1
&
4
"
2
" &
) " !
&
'
2
" &
4
"
" &
1 "
-
,
.
/
0
1
-
1 0
0
5 -
0
4
H
H
$
H
Input/Output Ports
相關PDF資料 |
PDF描述 |
|---|---|
| HT82J927A | USB Gamepad |
| HT82J97E | USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E-20SOP-A | USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E-28SOP-A | USB Joystick Encoder 8-Bit OTP MCU |
| HT82K28 | Win98 Keyboard Encoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82J927A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Gamepad |
| HT82J97A_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit MCU |
| HT82J97E | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit OTP MCU |
| HT82J97E_08 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit MCU |
| HT82J97E-20SOP-A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:USB Joystick Encoder 8-Bit OTP MCU |
發布緊急采購，3分鐘左右您將得到回復。