- 您現在的位置：買賣IC網 > PDF目錄385404 > HT82M9BEE (Holtek Semiconductor Inc.) USB Mouse Encoder 8-Bit MCU with EEPROM PDF資料下載
參數資料
| 型號： | HT82M9BEE |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | USB Mouse Encoder 8-Bit MCU with EEPROM |
| 中文描述： | USB鼠標編碼器8位微控制器帶有EEPROM |
| 文件頁數： | 20/47頁 |
| 文件大小： | 336K |
| 代理商： | HT82M9BEE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
Data EEPROM Timing Diagrams
Note: The write cycle time t
WR
is the time from a valid stop condition of a write sequence to the end of the valid start
condition of sequential command.
HT82M9BEE/HT82M9BAE
Rev. 1.20
20
August 13, 2007
$
"
/
=
% =
>
=
>
=
>
>
>
&
8
0 !
0 !
"
/
"
7 # -
/
! -
!
!
USB with MCU Interface
There are eight registers, including Pipe_ctrl, Address+Remote_WakeUp, STALL, SIES, MISC, Endpt_EN and
FIFO0~FIFO3 in this buffer function.
Register
Name
Pipe_ctrl
Addr.+
Remote
STALL
SIES
MISC
Endpt_EN FIFO0
FIFO1
FIFO2
FIFO3
Mem. Addr.
41H
42H
43H
45H
46H
47H
48H
49H
4AH
4BH
Register Memory Mapping
Address+Remote_WakeUp register represents current address and remote wake-up function. The initial value is
00000000 from MSB to LSB.
Register
Address
R/W
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
01000010B
R/W
Address value
Default value=00000000
Remote Wake-up Function
0: Not this function
1: The function exists
Address+Remote_WakeUp Register
STALL, Pipe_ctrl and Endpt_EN Registers
PIPE register represents whether the endpoint corresponding is accessed by host or not. After ACT_EN signal being
sent out, MCU can check which endpoint had been accessed. This register is set only after the time when host access
the corresponding endpoint.
STALLregister shows whether the endpoint corresponding works or not. As soon as the endpoint work improperly, the
bit corresponding must be set.
Pipe_ctrl register is used for configuring IN (Bit=1) or OUT (Bit=0) pipe. The default is define IN pipe. Where Bit0
(DATA0) of the Pipe_ctrl register is used to setting the data toggle of any endpoint (except endpoint 0) using data tog-
gles to the value DATA0. Once the user want the any endpoint (except endpoint 0) using data toggles to the value
DATA0, the user can output a LOW pulse to this bit. The LOW pulse period must at least 10 instruction cycle.
Endpt_EN register is used to enable or disable the corresponding endpoint (except endpoint 0). Enable Endpoint
(Bit=1) or disable Endpoint (Bit=0).
相關PDF資料 |
PDF描述 |
|---|---|
| HT82P604B | DC-DC Converter |
| HT82V14 | 14-Bit CCD/CIS Analog Signal Processor(14位CCD/CIS模擬信號處理器) |
| HT82V16 | 16-Bit CCD/CIS Analog Signal Processor(16位CCD/CIS模擬信號處理器) |
| HT82V24 | 16-Bit, 15MSPS, 3-Channel CCD/CIS Analog Signal Processor |
| HT82V26A | 16-Bit CCD/CIS Analog Signal Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT82P4352-16SOP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| HT82P604B | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:DC-DC Converter |
| HT82T20-20SOP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC |
| HT82V14 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:14-Bit CCD/CIS Analog Signal Processor |
| HT82V16 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:16-Bit CCD/CIS Analog Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。