- 您現在的位置：買賣IC網 > PDF目錄385407 > HT95AXXX (Holtek Semiconductor Inc.) I/O Type Phone 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT95AXXX |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | I/O Type Phone 8-Bit MCU |
| 中文描述： | I / O型電話8位微控制器 |
| 文件頁數： | 22/48頁 |
| 文件大小： | 360K |
| 代理商： | HT95AXXX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
HT95AXXX
Rev. 1.20
22
May 26, 2004
Dialer I/O Function
Aspecial dialer I/O circuit is built into the telephone controller for dialing application. These specially designed I/O cells
allows the controller to work under a low voltage condition that usually happens when the subscriber s loop is long.
Dialer I/O pin function:
Name
I/O
Description
XMUTE
NMOS Output
XMUTE pin output is controlled by software. This is an NMOS open drain structure
pulled to VSS during dialing signal transmission. Otherwise, it is an open circuit.
XMUTE is used to mute the speech circuit when transmitting the dialer signal.
DNPO
NMOS Output
DNPOpinisanNMOSoutput,usuallybymeansofsoftwaretomake/breaktheline.
This pin is only controlled by software.
PO
CMOS Output
This pin is controlled by the HKS, HFI and HDI pins.
When PO pin is high, the telephone line is make.
When PO pin is low, the telephone line is break.
HKS
Schmitt Trigger
Input
This pin controls the PO pin directly.
This pin is used to monitor the status of the hook-switch and its combination with
HFI/HDI can control the PO pin output to make or break the line.
A rising edge to HKS pin will cause the dialer I/O to be on-hook status and generate
an interrupt, its vector is 18H.
A falling edge to HKS pin will cause the dialer I/O to be off-hook status and clear HFO
andHDOflagsto0.Thisfallingedgewillalsogenerateaninterrupt,itsvectoris18H.
HDO
CMOS Output
Supported for HT95A400/40P, HT95A300/30P, HT95A200/20P
This pin is controlled directly by HDI, HKS and HFI pin.
When HDO pin is high, the hold-line function is enabled and PO outputs a high signal
to make the line.
HDI
Schmitt Trigger
Input
Supported for HT95A400/40P, HT95A300/30P, HT95A200/20P
A low pulse to HDI pin (hold-line function request) will clear HFO to 0 and toggle HDO
and generates an interrupt, its vector is 18H.
This pin controls the HFO and HDO pins directly.
This pin is functional only when the line is made, that is, off-hook or hand-free
(PO output high signal).
HFO
CMOS Output
This pin is controlled directly by HFI, HDI and HKS pins.
When HFO pin is high, the hand-free function is enabled and PO outputs a high
signal to make the line.
HFI
Schmitt Trigger
Input
A high pulse to HFI pin (hand-free function request) will clear HDO to 0 and toggle
HFO and generates an interrupt, its vector is 18H.
This pin controls the PO, HFO and HDO pins directly.
The following are the recommended circuit for HFI and HDI pins.
4 *
5
6 5
*
4 *
5
6
*
$
) # ) +
$
2
+
相關PDF資料 |
PDF描述 |
|---|---|
| HT95C20P | 8-Bit CID Type Phone Controller MCU |
| HT95C300 | 8-Bit CID Type Phone Controller MCU |
| HT95C30P | 8-Bit CID Type Phone Controller MCU |
| HT95C200 | 8-Bit CID Type Phone Controller MCU |
| HT95CXXX | CID Type Phone 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT95C200 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C20P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit CID Type Phone Controller MCU |
| HT95C300 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C30P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C400 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。