- 您現在的位置：買賣IC網 > PDF目錄385407 > HT95AXXX (Holtek Semiconductor Inc.) I/O Type Phone 8-Bit MCU PDF資料下載
參數資料
| 型號： | HT95AXXX |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | I/O Type Phone 8-Bit MCU |
| 中文描述： | I / O型電話8位微控制器 |
| 文件頁數： | 4/48頁 |
| 文件大小： | 360K |
| 代理商： | HT95AXXX |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Pin Name
I/O
Description
TMR1
I
Supported for HT95A400/40P, HT95A300/30P, HT95A200/20P
Schmitt trigger input for Timer/Event Counter 1.
No internal pull-high resistor.
Activated on falling or rising transition edge, selected by software.
Normal I/O
PA7~PA0
I/O
Bidirectional input/output ports.
Schmitt trigger input and CMOS output.
See mask option table for pull-high and wake-up function.
PB7~PB0
I/O
Bidirectional input/output ports.
Schmitt trigger input and CMOS output.
See mask option table for pull-high function
PD7~PD0
I/O
Bidirectional input/output ports.
Schmitt trigger input and CMOS output.
See mask option table for pull-high function
PE7~PE0
I/O
Bidirectional input/output ports.
Schmitt trigger input and CMOS output.
See mask option table for pull-high function
PF7~PF0
I/O
Bidirectional input/output ports.
Schmitt trigger input and CMOS output.
See mask option table for pull-high function
PG3~PG0
I/O
Bidirectional input/output ports.
Schmitt trigger input and CMOS output.
See mask option table for pull-high function
Dialer I/O (See the Dialer I/O Function )
HFI
I
Schmitt trigger input structure. An external RC network is recommended for input
debouncing.
This pin is pulled low with internal resistance of 200k
typ.
HFO
O
CMOS output structure.
HDI
I
Schmitt trigger input structure. An external RC network is recommended for input
debouncing.
This pin is pulled high with internal resistance of 200k
typ.
HDO
O
CMOS output structure.
HKS
I
This pin detects the status of the hook-switch and its combination with HFI/HDI can con-
trol the PO pin output to make or break the line.
PO
O
CMOS output structure controlled by HKS and HFI/HDI pins and which determines
whether the dialer connects or disconnects the telephone line.
DNPO
O
NMOS output structure.
XMUTE
O
NMOS output structure. Usually, XMUTE is used to mute the speech circuit when trans-
mitting the dialer signal.
Peripherals
DTMF
O
This pin outputs dual tone signals to dial out the phone number. The load resistor should
not be less than 5k .
MUSIC
O
This pin outputs the single tone that is generated by the PFD generator.
Absolute Maximum Ratings
Supply Voltage ..........................V
SS
0.3V to V
SS
+5.5V
Storage Temperature ........................... 50 C to 125 C
Input Voltage .............................. V
SS
0.3 to V
DD
+0.3V
Operating Temperature .......................... 20 C to 70 C
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliabil-
ity.
HT95AXXX
Rev. 1.20
4
May 26, 2004
相關PDF資料 |
PDF描述 |
|---|---|
| HT95C20P | 8-Bit CID Type Phone Controller MCU |
| HT95C300 | 8-Bit CID Type Phone Controller MCU |
| HT95C30P | 8-Bit CID Type Phone Controller MCU |
| HT95C200 | 8-Bit CID Type Phone Controller MCU |
| HT95CXXX | CID Type Phone 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT95C200 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C20P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:8-Bit CID Type Phone Controller MCU |
| HT95C300 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C30P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C400 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。