- 您現在的位置：買賣IC網 > PDF目錄385408 > HT95C300 (Holtek Semiconductor Inc.) 8-Bit CID Type Phone Controller MCU PDF資料下載
參數資料
| 型號： | HT95C300 |
| 廠商： | Holtek Semiconductor Inc. |
| 英文描述： | 8-Bit CID Type Phone Controller MCU |
| 中文描述： | 8位偵緝型電話MCU控制器 |
| 文件頁數： | 22/50頁 |
| 文件大小： | 324K |
| 代理商： | HT95C300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
HT95C200/20P/300/30P
Rev. 0.10
22
October 1, 2002
Preliminary
Register
Label
Bits
R/W
Function
FSKS
(2AH)
RDETF
0
RW
Ring or line reversal detect interrupt flag
1: Ring or line reversal detected
0: No ring or line reversal detected
This flag is set by hardware and cleared by software.
CDETF
1
RW
FSK carrier detect interrupt flag
1: An FSK carrier signal is detected
0: No valid FSK carrier signal is detected
This flag is set by hardware and cleared by software.
DOUT
2
RO
This flag presents the FSK decoder output when the decoder is at op-
eration mode. This data stream includes the alternate 1 and 0 pattern,
the marking and the data.
DOUTC
3
RO
This flag present the FSK decoder output like as the DOUT flag but
does not include the alternate 1 and 0 pattern.
4
RO
Unused bit, read as 0
FSKF
5
RW
FSK packet data interrupt flag
1: FSK packet data is ready
0: FSK packet data is not ready
This flag is set by hardware and cleared by software.
RINGF
6
RO
Thisflagpresentstheringcomingsignal.Refertothefollowingfigure.
7
RO
Unused bit, read as 0
FSKD
(2BH)
7~0
RO
FSK packet data register
;
<
E
;
>
;
3
9
Ring or Line reversal detect
When no signal is present on the telephone line, RDETI
will be at GND and RTIME is pulled to VDD by R1. If a
line reversal occurs, the RDETI pin will become high.
This causes RTIME and internal signal R_DET to be
pulled low. The C1 and R1 ensure that the R_DET sig-
nal is low during such a time, so that processor can de-
tect it.
When a ring occurs on the line, internal signal R_DET is
permanently low, indicating the envelope of the ring. If
the frequency of the ring must be measured, C1 may be
removed, RTIME and R_DET inverter follow RDETI.
The flag RDETF will go high when the R_DET signal
falling edge is detected. This may cause a peripheral in-
terrupt if RMSK is 0 and the peripheral interrupt is en-
abled (EPERI=1).
FSK data output
The FSK decoder will decode the FSK signal on the TIP
and RING line and produce two kinds of data formats,
the serial data and the 8-bit packet data. It also provides
the FSK carrier detection signal.
To enable the FSK decoder, the F_PWDN should be
written as 0. Once the FSK carrier signal is detected, the
flag CDETF will be set to 1. This may cause a peripheral
interrupt if CMSK is 0 and the peripheral interrupt is en-
abled.
The serial FSK data is present in two formats: RAW data
and COOK data, and could be monitored by the flag
DOUT, DOUTC, respectively.
The flag DOUT presents the output of the decoder when
the decoder is at operation mode. This data stream in-
cludes the alternate 1 and 0 pattern, the marking and
the data.
相關PDF資料 |
PDF描述 |
|---|---|
| HT95C30P | 8-Bit CID Type Phone Controller MCU |
| HT95C200 | 8-Bit CID Type Phone Controller MCU |
| HT95CXXX | CID Type Phone 8-Bit MCU |
| HT95L400-128QFP-A | LCD Type Phone 8-Bit MCU |
| HT95L100-64QEP-A | LCD Type Phone 8-Bit MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT95C30P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C400 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95C40P | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU |
| HT95CXXX | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
| HT95L000 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU |
發布緊急采購，3分鐘左右您將得到回復。