欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: HT95C300
廠商: Holtek Semiconductor Inc.
英文描述: 8-Bit CID Type Phone Controller MCU
中文描述: 8位偵緝型電話MCU控制器
文件頁數: 23/50頁
文件大小: 324K
代理商: HT95C300
HT95C200/20P/300/30P
Rev. 0.10
23
October 1, 2002
Preliminary
The flag DOUTC presents the output of the decoder
when the decoder is at operation mode. This data
stream is like the DOUT flag but does not include the al-
ternate 1 and 0 pattern.
If the FSK data is not detected, the DOUT and DOUTC
are held high.
Beside the serial data, the decoder also provides FSK
packet data. When decoder receives an FSK signal, it
will packet 10 bits data to 8 bits data, the first and 10th
bits will be discarded. When the 8-bit packet data is
valid, it will be stored in the FSK data register FSKD, the
FSK packet data interrupt flag FSKF will be set to 1. This
may cause a peripheral interrupt if FMSK is 0 and the
peripheral interrupt is enabled. The FSK packet source
could be DOUT or DOUTC, selected by FSKSEL. Note
that the start bit of the 10 packet bit should be 0, so the
MARK signal (one of the FSK data signals) will not be
packeted.
To detect the carrier signal or decode the serial data or
packet 10-bit data to 8-bit data, the operation mode of
the controller must be selected in Normal mode (proces-
sor running with 3.58MHz). When the operation mode is
Green or Sleep, FSK decoder will decode the wrong sig-
nal. However, when the operation mode is Green or
Sleep mode and the FSK decoder is at power down
mode (F_PWDN=1), the ring and line reversal detect is
still functional.
DTMF generator
The DTMF (Dual Tone Multiple-Frequency) signal gen-
erator is implemented in the telephone controller. It can
generate 16 dual tones and 8 single tones from the
DTMF pin. This generators also support power down,
tone on/off, burst mode function. The DTMF generator
clock source is 3.58MHz, before using this function, the
system operation mode must be at Normal mode.
The generator supports one interrupt source to the pe-
ripheral interrupt vector, namely DTMF burst-cycle inter-
rupt. Write 0 to the control flag, BMSK will enable this
interrupt. When the DTMF generator finishes 1
burst-cycle, the interrupt flag BURSTF will be set to 1 by
hardware even if the interrupt is disabled. This interrupt
willcauseaperipheralinterruptiftheperipheralinterrupt
is enabled. When the peripheral interrupt occurs, the in-
terrupt request flag PERF will be set and a subroutine
call to location 10H will occur. Return from the interrupt
subroutine, the interrupt flag BURSTF will not be
cleared by hardware, the user could clear it by software
if necessary. If this flag is not cleared, next burst inter-
rupt will occur.
The power down mode (D_PWDN=1) will terminate all
the DTMF generator function, however, the registers
DTMFC and DTMFD are accessible at this power down
mode.
"
8
'
'
'
<
1 "
F " % %
"
8
9 "
8
"
8
+ A C
"
9
" <
1 "
9
"
3 "
& % +
5 6
;
<
< E
7
1
<
1 "
0
' %
' %
8
" C
"
! 3
! 3
"
8
Note: *: If the flag FSKSEL=1, the sync signal data will not be packeted.
相關PDF資料
PDF描述
HT95C30P 8-Bit CID Type Phone Controller MCU
HT95C200 8-Bit CID Type Phone Controller MCU
HT95CXXX CID Type Phone 8-Bit MCU
HT95L400-128QFP-A LCD Type Phone 8-Bit MCU
HT95L100-64QEP-A LCD Type Phone 8-Bit MCU
相關代理商/技術參數
參數描述
HT95C30P 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
HT95C400 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
HT95C40P 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:LCD Type Phone 8-Bit MCU
HT95CXXX 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
HT95L000 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:CID Type Phone 8-Bit MCU
主站蜘蛛池模板: 松江区| 吉木乃县| 孟津县| 万源市| 延寿县| 锦屏县| 富宁县| 仁寿县| 荣成市| 新闻| 西吉县| 龙山县| 霍州市| 咸宁市| 阳信县| 锦州市| 曲靖市| 鄂托克旗| 漳浦县| 凤冈县| 聂拉木县| 汽车| 寿阳县| 江油市| 海晏县| 图木舒克市| 潜江市| 德安县| 绥宁县| 奉新县| 于都县| 龙井市| 平和县| 奉化市| 和田市| 荆州市| 根河市| 宁明县| 江山市| 浪卡子县| 宜兴市|