- 您現在的位置：買賣IC網 > PDF目錄385414 > HY29F002T (Hynix Semiconductor Inc.) 2 Megabit (256K x 8), 5 Volt-only, Flash Memory PDF資料下載
參數資料
| 型號： | HY29F002T |
| 廠商： | Hynix Semiconductor Inc. |
| 英文描述： | 2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
| 中文描述： | 2兆位（256K × 8），5伏只，閃存 |
| 文件頁數： | 7/38頁 |
| 文件大?。?/td> | 381K |
| 代理商： | HY29F002T |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
7
Rev. 4.1/May 01
HY29F002T
set operation is completed within a time of t
RP
. In
this case, the host can perform a read or write
operation t
RH
after the RESET# pin returns High.
The RESET# pin may be tied to the system reset
signal. Thus, a system reset would also reset the
device, enabling the system to read the boot-up
firmware from the Flash memory.
Sector Protect/Unprotect Operations
Hardware sector protection can be invoked to dis-
able program and erase operations in any single
sector or combination of sectors. This function is
typically used to protect data in the device from
unauthorized or accidental attempts to program
or erase the device while it is in the system (e.g.,
by a virus) and is implemented using program-
ming equipment. Sector unprotection re-enables
the program and erase operations in previously
protected sectors.
Table 1 identifies the seven sector in the top and
bottom boot block versions of the HY29F002T and
the address ranges that each covers. The device
is shipped with all sectors unprotected.
The sector protect/unprotect operations require a
high voltage (V
ID
) on address pin A[9] and the CE#
and/or OE# control pins, as detailed in Table 3.
When implementing these operations, note that
V
CC
must be applied to the device before applying
V
ID
, and that V
ID
should be removed before remov-
ing V
CC
from the device.
The flow chart in Figure 1 illustrates the proce-
dure for protecting sectors, and timing specifica-
tions and waveforms are shown in the specifica-
tions section of this document. Verification of pro-
tection is accomplished as described in the Elec-
tronic ID Mode section and shown in the flow chart.
The procedure for sector unprotection is illustrated
in the flow chart in Figure 2, and timing specifica-
tions and waveforms are given at the end of this
document.
Note that to unprotect any sector, all
unprotected sectors must first be protected prior
to the first unprotect write cycle.
Sectors can also be
temporarily
unprotected as
described in the next section.
Temporary Sector Unprotect Operation
This feature allows temporary unprotection of pre-
viously protected sectors to allow changing the
data in-system. Temporary Sector Unprotect
mode is activated by setting the RESET# pin to
V
ID
. While in this mode, formerly protected sec-
tors can be programmed or erased by invoking
the appropriate commands (see Device Com-
mands section). Once V
ID
is removed from RE-
SET#, all the previously protected sectors are pro-
tected again. Figure 3 illustrates the algorithm.
Electronic ID Mode Operation
The Electronic ID mode provides manufacturer and
device identification and sector protection verifi-
cation through identifier codes output on DQ[7:0].
This mode is intended primarily for programming
equipment to automatically match a device to be
programmed with its corresponding programming
algorithm. The Electronic ID information can also
be obtained by the host through a command se-
quence, as described in the Device Commands
section.
Operation in the Electronic ID mode requires V
ID
on address pin A[9], with additional requirements
for obtaining specific data items as listed in Table
2:
A read cycle at address 0xXXX00 retrieves the
manufacturer code (Hynix = 0xAD).
A read cycle at address 0xXXX01 returns the
device code (HY29F002T = 0xB0).
A read cycle containing a sector address (Table
1) in A[17:13] and the address 0x02 in A[7:0]
returns 0x01 if that sector is protected, or 0x00
if it is unprotected.
相關PDF資料 |
PDF描述 |
|---|---|
| HY29F002TC-90 | 2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
| HY29F002TT-45 | 2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
| HY29F002TT-55 | 2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
| HY29F002TT-70 | 2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
| HY29F002TT-90 | 2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY29F002TC-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002TC-12E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002TC-12I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| HY29F002TC-45 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:2 Megabit (256K x 8), 5 Volt-only, Flash Memory |
| HY29F002TC-45E | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。