欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: IS42S16800A-10T
廠商: INTEGRATED SILICON SOLUTION INC
元件分類: DRAM
英文描述: 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
中文描述: 8M X 16 SYNCHRONOUS DRAM, 7 ns, PDSO54
封裝: PLASTIC, TSOP2-54
文件頁數: 31/66頁
文件大小: 556K
代理商: IS42S16800A-10T
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
ADVANCED INFORMATION
Rev. 00A
06/01/02
31
ISSI
IS42S81600A, IS42S16800A, IS42S32400A
IS42LS81600A, IS42LS16800A, IS42LS32400A
DON'T CARE
UNDEFINED
CLK
COMMAND
DQ
READ
NOP
NOP
NOP
CAS Latency - 3
t
AC
t
OH
D
OUT
T0
T1
T2
T3
T4
t
LZ
CLK
COMMAND
DQ
READ
NOP
NOP
CAS Latency - 2
t
AC
t
OH
D
OUT
T0
T1
T2
T3
t
LZ
CAS LATENCY
CAS Latency
The CAS latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the
first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and the
latency is
m
clocks, the data will be available by clock edge
n +
m. The DQs will start driving as a result of the clock edge
one cycle earlier
(n + m
- 1), and provided that the relevant
access times are met, the data will be valid by clock edge
n +
m. For example, assuming that the clock cycle time is
such that all relevant access times are met, if a READ
command is registered at T0 and the latency is programmed
to two clocks, the DQs will start driving after T1 and the data
will be valid by T2, as shown in CAS Latency diagrams. The
Allowable Operating Frequency table indicates the operat-
ing frequencies at which each CAS latency setting can be
used.
Reserved states should not be used as unknown operation or
incompatibility with future versions may result.
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
CAS Latency
Allowable Operating Frequency (MHz)
Speed
CAS Latency = 2
CAS Latency = 3
7.5
100
133
10
75
100
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used
because unknown operation or incompatibility with future
versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9 = 1, the
programmed burst length applies to READ bursts, but write
accesses are single-location (nonburst) accesses.
相關PDF資料
PDF描述
IS42S32400A-10T 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S32400A-10TI CABLE ASSEMBLY; BNC MALE TO BNC FEMALE BULKHEAD; 50 OHM, RG174A/U COAX; ; *USES STANDARD 50 OHM INTERFACE CONNECTORS*
IS42S32400A-10TL CABLE ASSEMBLY; SMA MALE RIGHT ANGLE TO; SMA FEMALE BULKHEAD; 50 OHM, PE-SR405FL (.085" RE-SHAPABLE); 18" CABLE LENGTH;
IS42S32400A-10TLI 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A 16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
相關代理商/技術參數
參數描述
IS42S16800A-10TI 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-10TL 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-10TLI 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
IS42S16800A1-7TL 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:8Meg x16 128-MBIT SYNCHRONOUS DRAM
IS42S16800A-6T 制造商:ISSI 制造商全稱:Integrated Silicon Solution, Inc 功能描述:16Meg x 8, 8Meg x16 & 4Meg x 32 128-MBIT SYNCHRONOUS DRAM
主站蜘蛛池模板: 宁明县| 星座| 沅江市| 苗栗市| 扬州市| 兴宁市| 砀山县| 香港| 怀集县| 郓城县| 望江县| 涞源县| 松滋市| 盐山县| 封开县| 门头沟区| 安宁市| 榆社县| 郴州市| 惠州市| 安顺市| 综艺| 巴楚县| 邳州市| 枣阳市| 兴山县| 铜陵市| 建始县| 婺源县| 原阳县| 宝丰县| 太和县| 英超| 金沙县| 桐乡市| 灵寿县| 新津县| 江口县| 大庆市| 合阳县| 乾安县|