- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1106DH (NXP SEMICONDUCTORS) GT 10C 10#16 SKT PLUG PDF資料下載
參數資料
| 型號： | ISP1106DH |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 通用總線功能 |
| 英文描述： | GT 10C 10#16 SKT PLUG |
| 中文描述： | LINE TRANSCEIVER, PDSO16 |
| 封裝： | 4.40 MM, PLASTIC, MO-153, SOT-403-1, TSSOP-16 |
| 文件頁數： | 19/24頁 |
| 文件大小： | 588K |
| 代理商： | ISP1106DH |
Philips Semiconductors
ISP1105/1106/1107
Advanced USB transceivers
Product data
Rev. 06 — 30 November 2001
19 of 24
9397 750 08872
Koninklijke Philips Electronics N.V. 2001. All rights reserved.
14. Soldering
14.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
14.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 220
°
C for thick/large
packages, and below 235
°
C small/thin packages.
14.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1106W | GT 5C 5#16 PIN PLUG |
| ISP1107 | Advanced Universal Serial Bus transceiver |
| ISP1107DH | Advanced Universal Serial Bus transceivers |
| ISP1107W | Advanced Universal Serial Bus transceivers |
| ISP1109 | Universal Serial Bus transceiver with carkit support |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1106DH,112 | 功能描述:USB 接口集成電路 USB1.1 LOW VOLTAGE TRANSCEIVER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1106DH,118 | 功能描述:射頻收發器 USB1.1 LOW VOLTAGE TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1106DHAA | 功能描述:IC USB TRANSCEIVER 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISP1106DHTM | 功能描述:IC TXRX SERIAL BUS ADV 16TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| ISP1106W | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceivers |
發布緊急采購，3分鐘左右您將得到回復。