欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ISP1109
廠商: NXP Semiconductors N.V.
英文描述: Universal Serial Bus transceiver with carkit support
中文描述: 與車載通用串行總線收發器支持
文件頁數: 28/59頁
文件大小: 295K
代理商: ISP1109
9397 750 13355
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 14 July 2005
28 of 59
Philips Semiconductors
ISP1109
USB transceiver with carkit support
9.3 SPI interface
9.3.1
Pinout description
The SPI interface consists of four signals as given in
Table 37
.
9.3.2
Interface overview
The SPI interface has the following characteristics:
The maximum clock rate is 26 MHz.
Data is transmitted, most significant bit first. Each data field consists of a total of
32 bits.
The data and SPI_CLK signals are ignored, if SPI_CS is LOW. SPI_MISO is set to
three-state, if SPI_CS is programmed LOW.
SPI_CS is active (HIGH) only during the serial data transmission.
All input data is sampled at the rising edge of the SPI_CLK signal. Any transition on
SPI_MOSI must occur at least 5 ns before the rising edge of SPI_CLK and remain
stable for at least 5 ns after the rising edge of SPI_CLK.
All output data is updated at the rising edge of the SPI_CLK signal. Any transition on
SPI_MISO must occur at least 5 ns before the rising edge of SPI_CLK and remain
stable for at least 19.23 ns after the rising edge of SPI_CLK.
SPI_CS must be active (HIGH) at least 5 ns before the rising edge of the first
SPI_CLK signal, and must remain active (HIGH) at least 61.5 ns after the last falling
edge of SPI_CLK.
Coincident rising or falling edge of SPI_CLK and SPI_CS are not allowed.
If SPI_CS goes LOW before enough bits are sent, then the data bits sent are ignored.
When SPI_CS goes LOW to complete the SPI operation, the next rising edge of
SPI_CS must be delayed by at least 30 ns.
9.3.3
Interface protocol description
The SPI port is configured to use 32-bit serial data words, using 1 bit for R/W, 5 bits for
address, 1 bit for null, and 25 bits for data.
For each SPI transfer, a one is written to pin SPI_MOSI, if this SPI transfer is to be a write.
A zero is written to the pin, if this is to be a read-only command. If a zero is written, then
any data sent after the address bits is ignored and the internal contents of the field
addressed do not change when the 32
nd
SPI_CLK is sent. Next, the 5-bit address is
written to pin SPI_MOSI MSB first. Finally, data bits are written to the pin MSB first. Once
all the data bits are written, data is transferred to the actual registers on the 32
nd
SPI_CLK. SPI_CS must go LOW and return to HIGH to start the next SPI data transfer.
Table 37:
Pin name
SPI_MOSI
SPI_MISO
SPI_CLK
SPI_CS
SPI interface pin description
Description
serial data input line
serial data output line
clock input line
clock enable line (active HIGH)
相關PDF資料
PDF描述
ISP1109BS Universal Serial Bus transceiver with carkit support
ISP1122A Universal Serial Bus stand-alone hub
ISP1122ABD Universal Serial Bus stand-alone hub
ISP1122AD Universal Serial Bus stand-alone hub
ISP1122ANB Universal Serial Bus stand-alone hub
相關代理商/技術參數
參數描述
ISP1109BS 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver with carkit support
ISP1109BS,118 功能描述:射頻收發器 USB FS TRANSCVR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
ISP1109BS,151 功能描述:射頻收發器 DO NOT USE ORDER -T PART RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
ISP1109BS,157 功能描述:射頻收發器 DO NOT USE ORDER -T PART RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
ISP1109BSFE 功能描述:IC TXRX SERIAL BUS UNIV 32HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:2,500 系列:- 類型:驅動器 驅動器/接收器數:4/0 規程:RS422 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.154",3.90mm 寬) 供應商設備封裝:16-SOIC N 包裝:帶卷 (TR)
主站蜘蛛池模板: 扶余县| 盐津县| 鄂托克旗| 扶沟县| 嵊州市| 肃北| 武穴市| 永新县| 尉犁县| 永泰县| 若羌县| 涪陵区| 武汉市| 喀喇| 北川| 横山县| 旌德县| 唐山市| 蓬莱市| 平谷区| 莲花县| 永春县| 满城县| 阿拉善左旗| 连南| 正镶白旗| 大埔县| 西城区| 成武县| 罗山县| 慈利县| 中卫市| 景东| 鄯善县| 通化市| 双流县| 阿坝| 长武县| 长寿区| 淄博市| 建湖县|