- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1122A (NXP Semiconductors N.V.) Universal Serial Bus stand-alone hub PDF資料下載
參數資料
| 型號： | ISP1122A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus stand-alone hub |
| 中文描述： | 通用串行總線獨立的樞紐 |
| 文件頁數： | 20/48頁 |
| 文件大小： | 1150K |
| 代理商： | ISP1122A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Philips Semiconductors
ISP1122A
USB stand-alone hub
Preliminary specification
Rev. 01 — 27 March 2000
20 of 48
9397 750 06986
Philips Electronics N.V. 2000. All rights reserved.
9.4.6
Get configuration descriptor
The hub returns 25 bytes containing the configuration descriptor (9 bytes, see
Table 11
), the interface descriptor (9 bytes, see
Table 12
) and the endpoint descriptor
(7 bytes, see
Table 13
).
9.4.7
Get device descriptor
The hub returns 18 bytes containing the device descriptor, see
Table 10
.
9.4.8
Get hub descriptor
The hub returns 9 bytes containing the hub descriptor, see
Table 14
.
9.4.9
Get string descriptor (0)
The hub returns 4 bytes containing the language ID, see
Table 15
.
9.4.10
Get string descriptor (1)
The hub returns 46 bytes containing the manufacturer name, see
Table 15
.
9.4.11
Get string descriptor (2)
The hub returns 16 bytes containing the product name, see
Table 15
.
10. I
2
C-bus interface
A simple I
2
C-bus interface is provided in the ISP1122A to read customized vendor ID,
product ID and some other configuration bits from an external EEPROM. The
interface supports single master operation at a nominal bus speed of 93.75 kHz.
The I
2
C-bus interface is intended for bidirectional communication between ICs via two
serial bus wires, SDA (data) and SCL (clock). Both lines are driven by open-drain
circuits and must be connected to the positive supply voltage via pull-up resistors.
10.1 Protocol
The I
2
C-bus protocol defines the following conditions:
Bus free
: both SDA and SCL are HIGH
START
: a HIGH-to-LOW transition on SDA, while SCL is HIGH
STOP
: a LOW-to-HIGH transition on SDA, while SCL is HIGH
Data valid
: after a START condition, data on SDA are stable during the HIGH
period of SCL; data on SDA may only change while SCL is LOW.
Each device on the I
2
C-bus has a unique slave address, which the master uses to
select a device for access.
The master starts a data transfer using a START condition and ends it by generating
a STOP condition. Transfers can only be initiated when the bus is free. The receiver
must acknowledge each byte by means of a LOW level on SDA during the ninth clock
pulse on SCL.
For detailed information please consult The I
2
C-bus and how to use it, order number
9398 393 40011.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1122ABD | Universal Serial Bus stand-alone hub |
| ISP1122AD | Universal Serial Bus stand-alone hub |
| ISP1122ANB | Universal Serial Bus stand-alone hub |
| ISP1122 | Universal Serial Bus stand-alone hub |
| ISP1122BD | Universal Serial Bus stand-alone hub |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1122ABD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122AD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122ANB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
發布緊急采購，3分鐘左右您將得到回復。