- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1122A (NXP Semiconductors N.V.) Universal Serial Bus stand-alone hub PDF資料下載
參數資料
| 型號： | ISP1122A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus stand-alone hub |
| 中文描述： | 通用串行總線獨立的樞紐 |
| 文件頁數： | 9/48頁 |
| 文件大小： | 1150K |
| 代理商： | ISP1122A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Philips Semiconductors
ISP1122A
USB stand-alone hub
Preliminary specification
Rev. 01 — 27 March 2000
9 of 48
9397 750 06986
Philips Electronics N.V. 2000. All rights reserved.
6.2 Philips Serial Interface Engine (SIE)
The Philips SIE implements the full USB protocol layer. It is completely hardwired for
speed and needs no firmware intervention. The functions of this block include:
synchronization pattern recognition, parallel/serial conversion, bit (de-)stuffing, CRC
checking/generation, Packet IDentifier (PID) verification/generation, address
recognition, handshake evaluation/generation.
6.3 Hub repeater
The hub repeater is responsible for managing connectivity on a ‘per packet’ basis. It
implements ‘packet signalling’ and ‘resume’ connectivity. Low-speed devices can be
connected to downstream ports. If a low-speed device is detected the repeater will
not propagate upstream packets to the corresponding port, unless they are preceded
by a PREAMBLE PID.
6.4 End-of-frame timers
This block contains the specified EOF1 and EOF2 timers which are used to detect
‘loss-of-activity’ and ‘babble’ error conditions in the hub repeater. The timers also
maintain the low-speed keep-alive strobe which is sent at the beginning of a frame.
6.5 General and individual port controller
The general and individual port controllers together provide status and control of
individual downstream ports. Any port status change will be reported to the host via
the hub status change (interrupt) endpoint.
6.6 GoodLink
Indication of a good USB connection is provided through GoodLink technology. An
LED can be directly connected via an external 330
resistor.
During enumeration the LED blinks on momentarily. After successful configuration of
the ISP1122A, the LED is permanently on. The LED blinks off for 100 ms upon each
successful packet transfer (with ACK). The hub GoodLink indicator blinks when the
hub receives a packet addressed to it. Downstream GoodLink indicators blink upon
an acknowledgment from the associated port. In ‘suspend’ mode the LED is off.
This feature provides a user-friendly indication of the status of the hub, the connected
downstream devices and the USB traffic. It is a useful diagnostics tool to isolate faulty
USB equipment and helps to reduce field support and hotline costs.
6.7 Bit clock recovery
The bit clock recovery circuit recovers the clock from the incoming USB data stream
using a 4
×
oversampling principle. It is able to track jitter and frequency drift as
specified by the USB Specification Rev. 1.1
6.8 Voltage regulator
A 5 to 3.3 V DC-DC regulator is integrated on-chip to supply the analog transceiver
and internal logic. This can also be used to supply the terminal 1.5 k
pull-up resistor
on the D
+
line of the upstream connection.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1122ABD | Universal Serial Bus stand-alone hub |
| ISP1122AD | Universal Serial Bus stand-alone hub |
| ISP1122ANB | Universal Serial Bus stand-alone hub |
| ISP1122 | Universal Serial Bus stand-alone hub |
| ISP1122BD | Universal Serial Bus stand-alone hub |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1122ABD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122AD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122ANB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
| ISP1122D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus stand-alone hub |
發布緊急采購，3分鐘左右您將得到回復。