- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1123BD (NXP SEMICONDUCTORS) CAP .068UF 100V PPS FILM ECH-S PDF資料下載
參數資料
| 型號： | ISP1123BD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | CAP .068UF 100V PPS FILM ECH-S |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP32 |
| 封裝： | 7 X 7 X 1.40 MM, PLASTIC, LQFP-32 |
| 文件頁數： | 21/49頁 |
| 文件大小： | 1155K |
| 代理商： | ISP1123BD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Philips Semiconductors
ISP1123
USB compound hub
Preliminary specification
Rev. 01 — 5 October 1999
21 of 49
9397 750 06325
Philips Electronics N.V. 1999. All rights reserved.
11. I
2
C-bus interface
A simple I
2
C-bus interface is provided in the ISP1123 to read customized vendor ID,
product ID and some other configuration bits from an external EEPROM. The
interface supports single master operation at a nominal bus speed of 93.75 kHz.
The I
2
C-bus interface is intended for bidirectional communication between ICs via two
serial bus wires, SDA (data) and SCL (clock). Both lines are driven by open-drain
circuits and must be connected to the positive supply voltage via pull-up resistors.
11.1 Protocol
The I
2
C-bus protocol defines the following conditions:
Bus free
: both SDA and SCL are HIGH
START
: a HIGH-to-LOW transition on SDA, while SCL is HIGH
STOP
: a LOW-to-HIGH transition on SDA, while SCL is HIGH
Data valid
: after a START condition, data on SDA are stable during the HIGH
period of SCL; data on SDA may only change while SCL is LOW.
Each device on the I
2
C-bus has a unique slave address, which the master uses to
select a device for access.
The master starts a data transfer using a START condition and ends it by generating
a STOP condition. Transfers can only be initiated when the bus is free. The receiver
must acknowledge each byte by means of a LOW level on SDA during the ninth clock
pulse on SCL.
For detailed information please consult The I
2
C-bus and how to use it, order number
9398 393 40011.
11.2 Hardware connections
Via the I
2
C-bus interface the ISP1123 can be connected to an external EEPROM
(PCF8582 or equivalent). The hardware connections are shown in
Figure 6
.
The SCL and SDA pins are multiplexed with pins OPTION and INDV respectively.
Fig 6.
EEPROM connection diagram.
idth
MBL081
INDV/SDA
OPTION/SCL
A1
A2
A0
SDA
SCL
VDD
RP
RP
VDD
ISP1123
USB HUB
PCF8582
EEPROM
or
equivalent
I
2
C-bus
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1123 | Universal Serial Bus compound hub |
| ISP1123D | Universal Serial Bus compound hub |
| ISP1123NB | Universal Serial Bus compound hub |
| ISP1130 | Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1130DL | Universal Serial Bus compound hub with integrated keyboard controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1123D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub |
| ISP1123NB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub |
| ISP1130 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1130DL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1130N | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller |
發布緊急采購，3分鐘左右您將得到回復。