- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1521BE (NXP SEMICONDUCTORS) Hi-Speed Universal Serial Bus hub controller PDF資料下載
參數資料
| 型號： | ISP1521BE |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Hi-Speed Universal Serial Bus hub controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-315-1, LQFP-80 |
| 文件頁數： | 17/53頁 |
| 文件大?。?/td> | 270K |
| 代理商： | ISP1521BE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
Philips Semiconductors
ISP1521
Hi-Speed USB hub controller
Product data
Rev. 03 — 24 November 2004
17 of 53
9397 750 13702
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9.2 Device descriptors and string descriptors settings using I
2
C-bus
9.2.1
Background information on I
2
C-bus
The I
2
C-bus is suitable for bi-directional communication between ICs or modules. It
consists of two bi-directional lines: SDA for data signals and SCL for clock signals.
Both these lines must be connected to a positive supply voltage through a pull-up
resistor.
The basic I
2
C-bus protocol is defined as:
Data transfer is initiated only when the bus is not busy.
Changes in the data line occur when the clock is LOW and must be stable when
the clock is HIGH. Any changes in data lines when the clock is HIGH will be
interpreted as control signals.
Different conditions on I
2
C-bus:
The I
2
C-bus protocol defines the following
conditions:
Not busy —
both SDA and SCL remain HIGH
START —
a HIGH-to-LOW transition on SDA, while SCL is HIGH
STOP —
a LOW-to-HIGH transition on SDA, while SCL is HIGH
Data valid —
after a START condition, data on SDA must be stable for the duration of
the HIGH period of SCL.
Data transfer:
The master initiates each data transfer using a START condition and
terminates it by generating a STOP condition. To facilitate the next byte transfer, each
byte of data must be acknowledged by the receiver. The acknowledgement is done by
pulling the SDA line LOW on the ninth bit of the data. An extra clock pulse needs to
be generated by the master to accommodate this bit.
For more detailed information on the operation of the bus, refer to The I
2
C-bus
specification
I
2
C-bus address:
The address of the ISP1521 is given in
Table 10
.
Table 10:
I
2
C-bus slave address
MSB
A7
A6
0
0
Slave address
A4
1
LSB
A1
0
Bit
Value
A5
1
A3
0
A2
1
R/W
0/1
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1561 | ISP1561BM |
| ISP1561BM | ISP1561BM |
| ISP1562 | Hi-Speed Universal Serial Bus PCI Host Controller |
| ISP1562BE | Hi-Speed Universal Serial Bus PCI Host Controller |
| ISP1581 | Universal Serial Bus 2.0 high-speed interface device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1521BE,518 | 功能描述:USB 接口集成電路 USB2 7-PORT HUB CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1521BE,551 | 功能描述:USB 接口集成電路 USB2 7 PORT HUB RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1521BE,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1521BE518 | 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB HUB 80LQFP |
| ISP1521BE-S | 功能描述:IC USB HUB CONTROLLER HS 80-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。