- 您現在的位置：買賣IC網 > PDF目錄361014 > IXPD610 Industrial Control IC PDF資料下載
參數資料
| 型號： | IXPD610 |
| 英文描述： | Industrial Control IC |
| 中文描述： | 工業控制IC |
| 文件頁數： | 8/8頁 |
| 文件大小： | 182K |
| 代理商： | IXPD610 |
2001 IXYS/DEI All rights reserved
8
IXDP 610
have only one dead-time period in-
serted in each PWM cycle. In Fig. 6b
the desired ontime of OUT1 is less
than the one dead-time period, there-
fore OUT1 can never turn on. The
same is true for OUT2 in Fig. 6d. Fig.
6c is the normal situation, where both
outputs turn on and off during one
PWM cycle and, as a result, two
dead-time periods are inserted.
Response to a Change in the Pulse
Width Number
One can change the Pulse Width
number at any time. It is not
necessary to synchronize writes to
the Pulse Width latch with the CLK or
the PWM cycle period. The IXDP610
responds to the new Pulse Width
number three clock cycles after the
Pulse Width latch is loaded (1 CLK
cycle after WR goes high). Thus,
OUT1 and OUT2 will immediately
reflect the new Pulse Width number.
The IXDP610 does not wait until the
next PWM cycle to implement a
change in the Pulse Width number.
(See Fig. 7).
The resulting duty cycle is some-
where between the old and the new
duty cycle. The exact value of the
resulting duty cycle
depends on when
the Width Latch is loaded (1 CLK
cycle after WR goes high). Thus,
OUT1 and OUT2 will immediately
reflect the new Pulse Width number.
The IXDP610 does not wait until the
next PWM cycle to implement a
change in the Pulse Width number.
Fig. 7a shows what happens when the
Pulse Width number is changed from
20 % to 80 % near the middle of the
PWM cycle. Fig. 7b shows the reverse
situation.
The resulting duty cycle is somewhere
between the old and the new duty
cycle. The exact value of the resulting
duty cycle depends when the Width
latch is loaded (1 CLK cycle after WR
goes high). Thus, OUT1 and OUT2 will
immediately reflect the new Pulse
Width number. The IXDP610 does not
wait until the next PWM cycle to
implement a change in the Pulse Width
number.
Fig. 7 Effect of Changing the Duty
Cycle during a PWM Cycle
Fig. 6
Effect of Nonzero Dead-time on
PWM Waveform
on-time of an output is less than one
dead-time period, the output will not
turn on. This is shown in Fig. 6b and
6d. Therefore, the commanded duty
cycle and the actual duty cycle may
differ slightly, especially at extreme
duty cycle values.
Additionally, the dead-time can have
an effect on the voltage applied to
the load by the switching power
bridge; the exact effect is a function
of the direction of the current in the
bridge and the architecture of the
bridge. One should try and choose
the smallest dead-time that will work
with the given switch configuration.
Fig. 6.a and 6.e illustrate the two
duty cycle extremes, 0 % and 100 %.
In these two instances there will
never by a dead-time period, regard-
less of the value programmed in the
dead-time bits, because neither
output ever turns off. Fig. 6b and 6d
t
PW
= 0
t
PW
≤
t
DT
t
PW
> t
DT
t
PW
< (t
CYCL
- t
DT
)
t
PW
≥
(t
CYCL
- t
DT
)
t
PW
= t
CYCL
a)
b)
a)
b)
c)
d)
e)
相關PDF資料 |
PDF描述 |
|---|---|
| IXR100 | IXR100 - DISCONTINUED PRODUCT. No longer recommended for new design. |
| IXSA12N60AU1 | TRANSISTOR | IGBT | N-CHAN | 600V V(BR)CES | 24A I(C) | TO-263AA |
| IXSE502PI | Servo Encoder |
| IXSE503PC | Servo Encoder |
| IXSE503PI | Servo Encoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IXPN4004AR | 制造商:UNBRANDED 功能描述:CHARGER, NICAD, CHARGER UPGRADE KIT |
| IX-POLE-KIT | 制造商:PolyPhaser 功能描述:INTERCONNECT KIT |
| IXR100 | 制造商:BB 制造商全稱:BB 功能描述:Isolated, Self-Powered, Temperature Sensor Conditioning 4-20mA TWO-WIRE TRANSMITTER |
| IXRB5-506MINIPACK2 | 功能描述:IGBT 模塊 MiniPack 2 RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝: |
| IXRFD630 | 制造商:IXYS Corporation 功能描述:DRIVER MOSFET 30A DE275 制造商:IXYS Corporation 功能描述:DRIVER, MOSFET, 30A, DE275 |
發布緊急采購，3分鐘左右您將得到回復。