- 您現在的位置：買賣IC網 > PDF目錄30729 > LC07410LG SPECIALTY CONSUMER CIRCUIT, PBGA40 PDF資料下載
參數資料
| 型號： | LC07410LG |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA40 |
| 封裝： | 4.40 X 3.60 MM, FLGA-40 |
| 文件頁數： | 17/36頁 |
| 文件大小： | 367K |
| 代理商： | LC07410LG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LC07410LG
No.A1345-24/36
BEEP output
A signal input from the BEEP pin or a BEEP sound (pulse wave) generated within the IC can be output from the
speaker.
(a) EXT-BEEP operation
When BPMODE is 01, the signal input to the BEEP pin is output from the speaker.
(b) INT-BEEP operation
When BPMODE is 10/11, a BEEP signal generated within the IC is output from the speaker.
INTBPST
BEEP Output
Nrep
fsig
Ton
Toff
Use the BPHZ register to set the pulse frequency, fsig ,the BPTON and BPTOFF registers to set the on/off duty, and the
BPCNT register to set the repeat count, Nrep. Then set INTBPST = 0→1 to output the BEEP sound. Output stops
automatically when the specified number of beeps output.
When BPMODE is 10 (serial control mode), INTBPST control is carried out according to registers.
When BPMODE is 11 (parallel control mode), INTBPST control is carried out using the BEEP pin.
Note: When the transition INTBPST = 0→1 is detected, the BEEP sound starts. When BPMODE is 10 (serial control
mode), the BEEP sound is not output even if INTBPST = 1 is sent when INTBPST is set to 1.
If toff is 0, the continuous BEEP sound is output during the period given by ton*Nrep.
If Nrep is set to infinite, the ton/toff cycle repeats infinitely and stops when INTBPST is set to 0.
Output stops when INTBPST is set to 0, even in the middle of BEEP output.
The gain from the start of BEEP input until BTL output can be varied within the range -15dB to -21dB, based on the
SP_BPVOL[1:0] setting.
It is also possible to adjust the sound volume using an external resistor and by setting of 0dB.
[Againof approximately -21dB (typ) results with an external 100k
Ω connection.]
ADRS
Bit
Name
Init
Description
[7:6]
BPMODE
00b
BEEP output mode setting
11: INT-BEEP operation/parallel control mode
10: INT-BEEP operation/serial control mode
01: EXT-BEEP operation
00: OFF
13h
[5:4]
BPVOL
11b
BEEP gain selection
11: -21dB 10: -18dB 01: -15dB 00: 0dB
[7:5]
BPTON
010b
INT-BEEP on duty (ton) setting
2Fh
[4:0]
BPTOFF
00110b
INT-BEEP off duty (toff) setting
[7]
INTBPST
0b
INT-BEEP starting control (At BPMODE = 10, Valid)
[6:4]
BPHZ
011b
INT-BEEP frequency (fsig) setting
30h
[3:0]
BPCNT
0110b
INT-BEEP number of cycles (Nrep) setting
相關PDF資料 |
PDF描述 |
|---|---|
| LC07410LG | SPECIALTY CONSUMER CIRCUIT, PBGA40 |
| LC074146LP | 1 CHANNEL, AUDIO/VIDEO AMPLIFIER, QCC40 |
| LC074146LP | 1 CHANNEL, AUDIO/VIDEO AMPLIFIER, QCC40 |
| LC19001A010 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| LC403--CDC | SPECIALTY CONSUMER CIRCUIT, PDIP16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC074146LP | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Monaural CODEC+Audio I/F +Video driver IC |
| LC07422T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Audio CODEC with Video Driver |
| LC07424LP | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Audio CODEC with Video Driver |
| LC07424LP-MPB-E | 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
| LC08000E-2H | 制造商:ON Semiconductor 功能描述:MOTOR VECTOR CONTROL IC - Trays 制造商:ON Semiconductor 功能描述:FTRAY / MOTOR VECTOR CONTROL IC |
發布緊急采購，3分鐘左右您將得到回復。