- 您現在的位置：買賣IC網 > PDF目錄30737 > LC89058W-E SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | LC89058W-E |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, SQFP-48 |
| 文件頁數： | 30/46頁 |
| 文件大小： | 284K |
| 代理商： | LC89058W-E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
LC89058W-E
No.A1056-36/64
11 Description of General-purpose I/O Function (GPIO0, GPIO1, GPIO2, GPIO3)
11.1 Initial Settings
When setting general-purpose I/Os for input, pull down INT with a 10kΩ resistors. When settings general-purpose
I/Os for output, pull up INT with a 10k
Ω resistor. See Chapter 9 for INT pin settings.
If general-purpose I/Os are set to the output pin, the serial data input from the microcontroller interface is converted to
parallel data and output from of GPIO0, GPIO1, GPIO2, and GPIO3.
If general-purpose I/Os are set to the input pin, select one of the functions listed below with GPIOS.
(1) Store the parallel data input from the GPIO0, GPIO1, GPIO2, and GPIO3 in the internal register and readout the
contents of that register through the microcontroller interface (GPIOS=0).
(2) Configure a 2-to-1 (4 bits wide) selector that selects either the audio format data and clock that are input to the
GPIO0, GPIO1, GPIO2, and GPIO3 pins, or data and clock demodulated by the DIR block.
RMCK, RBCK, RLRCK, and RDATA are the outputs from the selector (GPIOS=1).
11.2 Output Function
The data output directed to the GPIO0, GPIO1, GPIO2, and GPIO3 are stored at CCB address 0xE8, command
address 10, input register bits DI12 to DI15, or register PI[3:0].
The data stored in PI[3:0] are transmitted out of the GPIO0, GPIO1, GPIO2, and GPIO3 pins.
11.3 Input Function
11.3.1 GPIOS=0
The data input to the GPIO0, GPIO1, GPIO2, and GPIO3 are taken into CCB address 0xEB, output register bits DO0
to DO3, or register PO[3:0].
The data must be readout by setting the interrupt source GPIO to INT or at an arbitrary timing. The way in which the
data is taken into the register depends on how it is readout.
11.3.1.1 GPIO=1 (using INT )
(1) XIN must always be given the specified clock and set in continuous operating mode (default).
(2) The data inputs to the GPIO0, GPIO1, GPIO2, and GPIO3 are taken into the register on a 24kHz clock.
(3) When the state of one of the data inputs changes, INT turns to “L” and suspends the data transfer to the register.
(4) The interrupt sources for CCB address 0xEA, output register DO14, and register OGPIO must be verified.
(5) INT turns “H” and the data is held in the register immediately when address 0xEA is readout.
(6) The read data from the PO[3:0] is transferred to the microcontroller. At the same time, the data in the register is
cleared.
(7) The contents of the register are updated if INT turns to “L” before P0[3:0] is readout.
11.3.1.2 GPIO=0 (not using INT )
(1) The data inputs to the GPIO0, GPIO1, GPIO2, and GPIO3 pins are taken in when the CCB address 0xEB is set.
(2) The data read from the PO[3:0] is transferred to the microcontroller. At the same time, the data in the register is
cleared.
相關PDF資料 |
PDF描述 |
|---|---|
| LC89058W-E | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| LC8905V | SPECIALTY CONSUMER CIRCUIT, PDSO24 |
| LC8910 | TRANSMITTER/RECEIVER IC, PDIP24 |
| LC8913 | TRANSMITTER/RECEIVER IC, PDIP40 |
| LC8912 | TRANSMITTER/RECEIVER IC, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC8905V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver |
| LC89060 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video D/A Converters |
| LC89060M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video D/A Converters |
| LC89066 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video A/D Converters |
| LC89066M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6-Bit Video A/D Converters |
發布緊急采購，3分鐘左右您將得到回復。