- 您現在的位置：買賣IC網 > PDF目錄30742 > LIS2L06AL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA8 PDF資料下載
參數資料
| 型號： | LIS2L06AL |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| 封裝： | 5 X 5 MM, 1.60 MM HEIGHT, PLASTIC, LGA-8 |
| 文件頁數： | 16/17頁 |
| 文件大?。?/td> | 202K |
| 代理商： | LIS2L06AL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁
Mechanical and electrical specifications
LIS2L06AL
8/17
Self Test allows to test the mechanical and electric part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self Test function is off when
the ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force is applied
to the sensor, simulating a definite input acceleration. In this case the sensor outputs will
exhibit a voltage change in their DC levels which is related to the selected full scale and
depending on the Supply Voltage through the device sensitivity. When ST is activated, the
device output level is given by the algebraic sum of the signals produced by the acceleration
acting on the sensor and by the electrostatic test-force. If the output signals change within
the amplitude specified inside Table 2, than the sensor is working properly and the
parameters of the interface chip are within the defined specification.
Output impedance describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 1nF and the internal
resistor. Due to the high resistor level only small, inexpensive external capacitors are
needed to generate low corner frequencies. When interfacing with an ADC it is important to
use high input impedance input circuitries to avoid measurement errors. Note that the
minimum load capacitance forms a corner frequency beyond the resonance frequency of
the sensor. For a flat frequency response a corner frequency well below the resonance
frequency is recommended. In general the smallest possible bandwidth for an particular
application should be chosen to get the best results.
相關PDF資料 |
PDF描述 |
|---|---|
| LIS2L06ALTR | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS302ALB | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS302ALBTR | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS3L02AS4 | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| LM0555N | PULSE; RECTANGULAR, TIMER, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS2L06AL_06 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR:2-axis - +/- 2g/6g ultracompact linear accelerometer |
| LIS2L06ALTR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 2 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2MDLTR | 功能描述:ULTRA-COMPACT HIGH-PERFORMANCE E 制造商:stmicroelectronics 系列:- 零件狀態:在售 類型:羅盤/磁力計 技術:磁阻 軸:X，Y，Z 輸出類型:I2C，SPI 電壓 - 電源:1.71 V ~ 3.6 V 分辨率:16 b 帶寬:5Hz ~ 50Hz 工作溫度:-40°C ~ 85°C（TA） 特性:可選數值范圍 封裝/外殼:12-VFLGA 供應商器件封裝:12-LGA（2x2） 標準包裝:1 |
| LIS302ALB | 功能描述:加速計 - 板上安裝 MEMS motion snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302ALBTR | 功能描述:加速計 - 板上安裝 MEMS Motion Sensor RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。