- 您現在的位置：買賣IC網 > PDF目錄361028 > LM3916 (National Semiconductor Corporation) Dot/Bar Display Driver PDF資料下載
參數資料
| 型號： | LM3916 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Dot/Bar Display Driver |
| 中文描述： | 點/酒吧顯示驅動程序 |
| 文件頁數： | 11/27頁 |
| 文件大小： | 509K |
| 代理商： | LM3916 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Application Hints
(Continued)
Peak Program Meter
The VU meter, originally intended for signals sent via tele-
phone lines, has shortcomings when used in high fidelity
systems. Due to its slow response time, a VU meter will not
accurately display transients that can saturate a magnetic
tape or drive an amplifier into clipping. The fast-attack peak
program meter (PPM) which does not have this problem is
becoming increasingly popular.
While several European organizations have specifications
for peak program meters, the German DIN specification
45406 is becoming a de facto standard. Rather than respond
instantaneously to peak, however, PPM specifications re-
quire a finite “integration time” so that only peaks wide
enough to be audible are displayed. DIN 45406 calls for a re-
sponse of 1 dB down from steady-state for a 10 ms tone
burst and 4 dB down for a 3 ms tone burst. These require-
ments are consistent with the other frequently encountered
spec of 2 dB down for a 5 ms burst and are met by an attack
time constant of 1.7 ms.
The specified return time of 1.5s to 20 dB requires a
650 ms decay time constant. The full-wave peak detector of
Figure 6 satisfies both the attack and decay time criteria.
Cascading The LM3916
The LM3916 by itself covers the 23 dB range of the conven-
tional VU meter. To display signals of 40 dB or 70 dB dy-
namic range, the LM3916 may be cascaded with the 3 dB/
step LM3915s.Alternatively, two LM3916s may be cascaded
for increased resolution over a 28 dB range. Refer to the Ex-
tended Range VU Meter and High Resolution VU Meter in
the Typical Applications section for the complete circuits for
both dot and bar mode displays.
To obtain a display that makes sense when an LM3915 and
an LM3916 are cascaded, the 20 dB output from the
LM3916 is dropped. The full-scale display for the LM3915 is
set at 3 dB below the LM3916’s 10 dB output and the rest
of the thresholds continue the 3 dB/step spacing. A simple,
low cost approach is to set the reference voltage of the two
chips 16 dB apart as in Figure 5 The LM3915, with pin 8
grounded, runs at 1.25V full-scale. R1 and R2 set the
LM3916’s reference 16 dB higher or 7.89V. Variation in the
two on-chip references and resistor tolerance may cause a
±
1 dB error in the 10 dB to 13 dB transition. If this is ob-
jectionable, R2 can be trimmed.
The drawback of the aforementioned approach is that the
threshold of LED
#
1 on the LM3915 is only 56 mV. Since
comparator offset voltage may be as high as 10 mV, large er-
rors can occur at the first few thresholds. A better approach,
as shown in Figure 9 is to keep the reference the same for
DS007971-14
Design Equations
GAIN
1
10
R5
100k
1M
R6
43k
100k
C2
2.0
1.0
C3
0.56 μF
0.056 μF
FIGURE 7. Full-Wave Average Detector to VU Meter Specifications
*
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM3916N | Dot/Bar Display Driver |
| LM3916N-1 | 6 PIN MINI DIN CABLE MM 50FT |
| LM395 | Ultra Reliable Power Transistors |
| LM395T | Ultra Reliable Power Transistors |
| LM399 | Precision Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3916J/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Vacuum Fluorescent Display Driver |
| LM3916N | 制造商:Texas Instruments 功能描述:IC DISPLAY DRIVER 3916 DIP18 制造商:Rochester Electronics LLC 功能描述: |
| LM3916N/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Vacuum Fluorescent Display Driver |
| LM3916N/B+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Vacuum Fluorescent Display Driver |
| LM3916N1 | 制造商:National Semiconductor 功能描述:LED DRVR 10Segment 3.3V/5V/9V/12V/15V/18V/24V 18-Pin PDIP Tube |
發布緊急采購，3分鐘左右您將得到回復。