- 您現在的位置：買賣IC網 > PDF目錄361034 > LM81 (National Semiconductor Corporation) Serial Interface ACPI-Compatible Microprocessor System PDF資料下載
參數資料
| 型號： | LM81 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System |
| 中文描述： | 串行接口ACPI的兼容微處理器系統 |
| 文件頁數： | 3/32頁 |
| 文件大小： | 412K |
| 代理商： | LM81 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Pin Description
(Continued)
Pin
Name(s)
Pin
Number
4
5-6
7
Number
of Pins
1
2
1
Type
Description
SMBCLK
FAN1-FAN2
CI
Digital Input
Digital Inputs
Digital I/O
Serial Bus Clock.
Schmitt Trigger fan tachometer inputs.
An active high input from an external circuit which latches a
Chassis Intrusion event. This line can go high without any
clamping action regardless of the powered state of the LM81.
There is also an internal open-drain output on this line, controlled
by Bit 6 of the Configuration Register (40h) or Bit 7 CI Clear
Register (46h), to provide a minimum 20 ms reset pulse. See
Section 3.3 and Section 9.0
Critical Temperature Alarm active low open-drain output. This pin
can be grounded when not used.
+3.3V V
+
power. Bypass with the parallel combination of 10 μF
(electrolytic or tantalum) and 0.1 μF (ceramic) bypass capacitors.
Interrupt active low open-drain output. This output is enabled when
Bit 1 in the Configuration Register is set to 1. The default state is
disabled.
0V to +1.25V amplitude 8-bit DAC output. When forced high by an
external voltage the NAND Tree Test mode is enabled which
provides board-level connectivity testing. Refer to Section 11.0 on
NAND Tree testing.
Master Reset, 5 mA driver (open-drain), active low output with a
20 ms minimum pulse width. Available when enabled via Bit 4 in
the Configuration register. It acts as an active low power on
RESET input.
Internally connected to all circuitry. The ground reference for all
analog inputs and the DAC output. This pin needs to be
connected to a low noise analog ground plane for optimum
performance of the DAC output.
Analog input for monitoring 12V or Vccp2. Selectable by
choosing the appropriate external resistor divider values such that
the input to the LM81 is scaled to +2.5V. See Section 4.0.
Analog input for monitoring +12V.
Analog input for monitoring +5V.
Analog input for monitoring +3.3V.
Analog input for monitoring +2.5V.
Analog input for monitoring Vccp, a processor voltage that is
nominally at +2.5V.
Supply Voltage readouts from the Pentium/PRO power supplies
that indicate the operating voltage or the processor (e.g. 1.5V to
2.9V). The values are read in the VID/Fan Divisor Register and
the VID4 Register.
T_CRIT_A
8
1
Digital Output
V
+
(+2.8V to
+3.8V)
INT
9
1
POWER
10
1
Digital Output
DACOut/NTEST_IN
11
1
Analog
Output/Digital
Input
RESET
12
1
Digital I/O
GND
13
1
GROUND
Vccp2
14
1
Analog Input
+12Vin
+5Vin
+3.3Vin
+2.5Vin
Vccp1
15
16
17
18
19
1
1
1
1
1
Analog Input
Analog Input
Analog Input
Analog Input
Analog Input
VID4-VID0
20-24
5
Digital Inputs
TOTAL PINS
24
www.national.com
3
相關PDF資料 |
PDF描述 |
|---|---|
| LM81CIMT-31 | Serial Interface ACPI-Compatible Microprocessor System |
| LM82CIMQAX | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM82CIMQA | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM82 | Remote Diode and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8300HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8-1 | 制造商:Banner Engineering 功能描述:Logic Module; Delayed One-Shot; ,Ranges For Banner Multi-Beam Sensor Blocks 制造商:Banner Engineering 功能描述:3-And 4-Wire Logic Modules |
| LM81_02 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM810 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:3-Pin Microprocessor Reset Circuits |
| LM810A-2.63 E WAF | 制造商:Texas Instruments 功能描述: |
| LM810A-2.93 E WAF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。