- 您現在的位置：買賣IC網 > PDF目錄361035 > LM9040M (NATIONAL SEMICONDUCTOR CORP) Dual Lambda Sensor Interface Amplifier PDF資料下載
參數資料
| 型號： | LM9040M |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 測量放大器 |
| 英文描述： | Dual Lambda Sensor Interface Amplifier |
| 中文描述： | DUAL INSTRUMENTATION AMPLIFIER, PDSO14 |
| 封裝： | 0.300 INCH, PLASTIC, SOP-14 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 178K |
| 代理商： | LM9040M |
Common Mode Filtering
(Continued)
For a common mode sine wave signal having a frequency
100 Hz, and with a F
CLOCK
of 100 kHz, the minimum com-
mon mode rejection would be:
CMRR
e
2
#
3.14159
#
100
#
5E-6
#
4.53
CMRR
e
0.014
e b
37 dB
If the common mode sine wave has a peak to peak value of
2V, the maximum voltage error at the output would be:
V
OUT(CM)
e
2V
#
0.014
e
28 mV
As this formula shows, the value of V
OUT(CM)
is proportional
to the frequency of the CMR signal. If the frequency is dou-
bled, the value of V
OUT(CM)
is also doubled. The addition of
a small bypass capacitor (C
CM
) from the non-inverting input
to ground will help counter this problem. SeeFigure 6. How-
ever, the use of this bypass capacitor creates a new prob-
lem in that the differential input is no longer balanced. While
the Lambda sensor is cold (i.e. R
SENSOR
l
10 Meg
X
) there
is little difference in CMR performance. As the Lambda sen-
sor heats to the operating temperature and the sensor re-
sistance decreases, the common mode signal is no longer
applied to both inputs equally. This imbalance causes
V
OUT(CM)
to increase as R
SENSOR
decreases, as the non-
inverting input will see the full common mode signal, while
the non-inverting input will see an attenuated common
mode signal.
The selection of the value of the CMR bypass capacitor
needs to be balanced with the need for reasonable reduc-
tion, or elimination, of common mode signals with both cold
and hot sensors. Since normal operation will need to in-
clude consideration of the entire impedance range of the
sensor, a trade off in overall application performance may
be needed.
Generally, the value of the CMR bypass capacitor should be
kept as low as possible, and should not be larger than the
differential input filter capacitor. Values in the range of
0.001
m
F to 0.01
m
F will usually provide reasonable CMR
results, but optimum results will need to be determined em-
pirically, as the source of common mode signals will be
unique to each application.
Gain and Filter Stage
The signal gain and filter stage is designed to have a DC
gain of 4.53 V/V, with a cut-off frequency of typically
500 Hz. The external 4 k
X
resistors on each input pin are in
series with the differential input impedance. Together they
form a voltage divider circuit across the input such that the
net DC gain of the application circuit is 4.50 V/V.
TL/H/12372–17
FIGURE 7. Simplified Gain and Filter Circuit
The internal gain is set by the ratio of C
IN
and C
FB
:
GAIN
DC
e
C
IN
C
FB
GAIN
DC
e
7.4213 pF
1.6383 pF
e
4.53 V/V
The corner frequency (
b
3 dB) is set by the ratio of C
FB
and
C
INT
, and by F
CLOCK
:
F
C
e
F
CLOCK
#
C
FB
2
#
q
#
C
INT
1E5
#
1.6383E-12
2
#
3.14159
#
52.1E-12
F
C
e
e
500 Hz
TL/H/12372–18
FIGURE 8. Equivalent Gain and Filter Circuit
6
相關PDF資料 |
PDF描述 |
|---|---|
| LM9044 | LM9044 Lambda Sensor Interface Amplifier |
| LM9044V | LM9044 Lambda Sensor Interface Amplifier |
| LM9061 | Power MOSFET Driver with Lossless Protection |
| LM9061N | Power MOSFET Driver with Lossless Protection |
| LM9070 | Low-Dropout System Voltage Regulator with Keep-Alive ON/OFF Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9040M/NOPB | 功能描述:IC SENSOR DUAL INTER AMP 14-SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| LM9040MX | 功能描述:IC AMP DUAL SENSR INTERFC 14SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| LM9040MX/NOPB | 制造商:Texas Instruments 功能描述:Lambda Sensor Interface Amplifier 14-Pin SOIC W T/R |
| LM9044 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9044 Lambda Sensor Interface Amplifier |
| LM9044V | 功能描述:差分放大器 RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。