
Absolute Maximum Ratings
(Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Input Voltage, Pin 3
Supply Voltage, Pin 4
Output Voltage, Pin 8
Voltage at All Other Pins
Output Current, Pin 8
Package Dissipation
Operating Temperature Range (T
A
)
2 V
p–p
10V
13V
Vs to Gnd
30 mA
500 mW
25C to +125C
Storage Temperature Range
Soldering Information
Dual-In-Line Package
Soldering (10 sec.)
Small Outline Package
Vapor Phase (60 sec.)
Infrared (15 sec.)
See AN-450 “Surface Mounting Methods and Their Effect
on Product Reliability” for other methods of soldering
surface mount devices.
55C to +150C
260C
215C
220C
Electrical Characteristics
Test Circuit, T
A
= 25C, V
s
= 5V, RtCt
#
2, Sw. 1 Pos. 0, and no input, unless otherwise noted.
Symbol
Parameter
I4
Power Supply
Current
or Activated
Conditions
Min
Typ
0.3
0.5
0.8
0
40
1
98
103
105
Max
Units
RtCt
#
1, Quiescent
V
s
= 2V
V
s
= 5V
V
s
= 9V
mAdc
0.8
1.3
V3
R3
I8
f
0
Input D.C. Bias
Input Resistance
Output Leakage
Center Frequency,
F
osc
÷
2
mVdc
k
nAdc
100
RtCt
#
2, Measure Oscillator
Frequency and Divide by 2
V
s
= 2V
V
s
= 5V
V
s
= 9V
kHz
92
113
f
0
Center Frequency
Shift with Supply
1.0
2.0
%/V
V
in
Input Threshold
Set Input Frequency Equal to f
0
Measured Above, Increase Input Level
Until Pin 8 Goes Low.
V
s
= 2V
V
s
= 5V
V
s
= 9V
11
17
20
30
45
27
45
mVrms
V
in
Input Hysteresis
Starting at Input Threshold, Decrease Input
Level Until Pin 8 goes High.
Input Level
>
Threshold
Choose RL for Specified I8
1.5
mVrms
V8
Output ’Sat’ Voltage
I8 = 2 mA
I8 = 20 mA
V
s
= 2V
0.06
0.7
0.15
Vdc
L.D.B.W.
Largest Detection
Bandwidth
Measure F
osc
with Sw. 1 in
Pos. 0, 1, and 2;
7
11
15
%
V
s
= 5V
11
14
17
V
s
= 9V
15
BW
Bandwidth Skew
0
±
1.0
%
f
max
Highest Center
Freq.
Input Threshold at
f
max
RtCt
#
3, Measure Oscillator Frequency and Divide by 2
700
kHz
V
in
Set Input Frequency Equal to f
max
measured Above,
Increase Input Level Until Pin 8 goes Low.
35
mVrms
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func-
tional, but do not guarantee specific performance limits. Electrical Characteristics state DC andAC electrical specifications under particular test conditions which guar-
antee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is
given, however, the typical value is a good indication of device performance.
www.national.com
2