- 您現在的位置：買賣IC網 > PDF目錄361036 > LMC567 (National Semiconductor Corporation) Low Power Tone Decoder PDF資料下載
參數資料
| 型號： | LMC567 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Low Power Tone Decoder |
| 中文描述： | 低功耗音頻解碼器 |
| 文件頁數： | 5/7頁 |
| 文件大小： | 168K |
| 代理商： | LMC567 |
Applications Information
(refer to Block
Diagram) (Continued)
SUPPLY DECOUPLING
The decoupling of supply pin 4 becomes more critical at high
supply voltages with high operating frequencies, requiring
C4 to be placed as close as possible to pin 4.
INPUT PIN
The input pin 3 is internally ground-referenced with a nomi-
nal 40 k
resistor. Signals which are already centered on 0V
may be directly coupled to pin 3; however, any d.c. potential
must be isolated via a coupling capacitor. Inputs of multiple
LMC567 devices can be paralleled without individual d.c.
isolation.
LOOP FILTER
Pin 2 is the combined output of the phase detector and con-
trol input of the VCO for the phase-locked loop (PLL). Ca-
pacitor C2 in conjunction with the nominal 80 k
pin 2 inter-
nal resistance forms the loop filter.
For small values of C2, the PLL will have a fast acquisition
time and the pull-in range will be set by the built in VCO fre-
quency stops, which also determine the largest detection
bandwidth (LDBW). Increasing C2 results in improved noise
immunity at the expense of acquisition time, and the pull-in
range will begin to become narrower than the LDBW (see
Bandwidth as a Function of C2 curve). However, the maxi-
mum hold-in range will always equal the LDBW.
OUTPUT FILTER
Pin 1 is the output of a negative-going amplitude detector
which has a nominal 0 signal output of 7/9 V
. When the PLL
is locked to the input, an increase in signal level causes the
detector output to move negative. When pin 1 reaches
2/3 V
s
the output is activated (see OUTPUT PIN).
Capacitor C1 in conjunction with the nominal 40 k
pin 1 in-
ternal resistance forms the output filter. The size of C1 is a
tradeoff between slew rate and carrier ripple at the output
comparator. Low values of C1 produce the least delay be-
tween the input and output for tone burst applications, while
larger values of C1 improve noise immunity.
Pin 1 also provides a means for shifting the input threshold
higher or lower by connecting an external resistor to supply
or ground. However, reducing the threshold using this tech-
nique increases sensitivity to pin 1 carrier ripple and also re-
sults in more part to part threshold variation.
OUTPUT PIN
The output at pin 8 is an N-channel FET switch to ground
which is activated when the PLL is locked and the input tone
is of sufficient amplitude to cause pin 1 to fall below 2/3 V
s
.
Apart from the obvious current component due to the exter-
nal pin 8 load resistor, no additional supply current is re-
quired to activate the switch. The on resistance of the switch
is inversely proportional to supply; thus the “sat” voltage for
a given output current will increase at lower supplies.
www.national.com
5
相關PDF資料 |
PDF描述 |
|---|---|
| LMC567CM | Low Power Tone Decoder |
| LMC567CN | Low Power Tone Decoder |
| LMC568 | Low Power Phase-Locked Loop |
| LMC568CM | Low Power Phase-Locked Loop |
| LMC568CN | Low Power Phase-Locked Loop |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMC567CM | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| LMC567CM NOPB | 制造商:National Semiconductor 功能描述:Tone Decoder 8-Pin SOIC N T/R |
| LMC567CM/NOPB | 功能描述:電話振鈴器 Low Power Tone Decoder RoHS:否 制造商:NJR 產品:FSK Demodulator / Tone Decoder 封裝 / 箱體:DIP-14 頻率:0.01 Hz to 300 KHz 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| LMC567CM/NOPB | 制造商:Texas Instruments 功能描述:Tone Decoder IC |
| LMC567CMX | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。