- 您現在的位置：買賣IC網 > PDF目錄361039 > LMC7660IN (NATIONAL SEMICONDUCTOR CORP) Switched Capacitor Voltage Converter PDF資料下載
參數資料
| 型號： | LMC7660IN |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Switched Capacitor Voltage Converter |
| 中文描述： | SWITCHED CAPACITOR CONVERTER, 10 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 4/12頁 |
| 文件大小： | 134K |
| 代理商： | LMC7660IN |
Typical Performance Characteristics
(Continued)
Application Information
Circuit Description
The LMC7660 contains four large CMOS switches which are
switched in a sequence to provide supply inversion V
=
V
. Energy transfer and storage are provided by two inex-
pensive electrolytic capacitors. Figure 2 shows how the
LMC7660 can be used to generate V
+
from V
+
. When
switches S1 and S3 are closed, C
charges to the supply
voltage V
+
. During this time interval, switches S2 and S4 are
open.After C
charges to V
+
, S1 and S3 are opened, S2 and
S4 are then closed. By connecting S2 to ground, C
p
devel-
ops a voltage V
/2 on C
.After a number of cycles C
will be
pumped to exactly V
+
. This transfer will be exact assuming
no load on C
r
, and no loss in the switches.
In the circuit of Figure 2 S1 is a P-channel device and S2,
S3, and S4 are N-channel devices. Because the output is bi-
ased below ground, it is important that the p
wells of S3 and
S4 never become forward biased with respect to either their
sources or drains. A substrate logic circuit guarantees that
these p
wells are always held at the proper voltage. Under
all conditions S4 p
well must be at the lowest potential in the
circuit. To switch off S4, a level translator generates V
=
0V, and this is accomplished by biasing the level translator
from the S4 p
well.
An internal RC oscillator and
÷
2 circuit provide timing sig-
nals to the level translator. The built-in regulator biases the
oscillator and divider to reduce power dissipation on high
supply voltage. The regulator becomes active at about V
+
=
6.5V. Low voltage operation can be improved if the LV pin is
shorted to ground for V
+
≤
3.5V. For V
+
≥
3.5V, the LV pin
must be left open to prevent damage to the part.
Power Efficiency and Ripple
It is theoretically possible to approach 100% efficiency if the
following conditions are met:
1. The drive circuitry consumes little power.
2. The power switches are matched and have low R
on
.
3. The impedance of the reservoir and pump capacitors are
negligibly small at the pumping frequency.
The LMC7660 closely approaches 1 and 2 above. By using
a large pump capacitor C
, the charge removed while sup-
plying the reservoir capacitor is small compared to C
’s total
charge. Small removed charge means small changes in the
pump capacitor voltage, and thus small energy loss and high
efficiency. The energy loss by C
p
is:
By using a large reservoir capacitor, the output ripple can be
reduced to an acceptable level. For example, if the load cur-
rent is 5 mA and the accepted ripple is 200 mV, then the res-
ervoir capacitor can omit approximately be calculated from:
Precautions
1. Do not exceed the maximum supply voltage or junction
temperature.
2. Do not short pin 6 (LV terminal) to ground for supply volt-
ages greater than 3.5V.
3. Do not short circuit the output to V
+
.
4. External electrolytic capacitors C
and C
should have
their polarities connected as shown in Figure 1
Replacing Previous 7660 Designs
To prevent destructive latchup, previous 7660 designs re-
quire a diode in series with the output when operated at el-
evated temperature or supply voltage. Although this pre-
vented the latchup problem of these designs, it lowered the
available output voltage and increased the output series re-
sistance.
The National LMC7660 has been designed to solve the in-
herent latch problem. The LCM7660 can operate over the
entire supply voltage and temperature range without the
need for an output diode. When replacing existing designs,
the LMC7660 can be operated with diode Dx.
Unloaded Oscillator Frequency
as a Function of Temperature
DS009136-24
Output R vs Supply Voltage
DS009136-25
P
eff
vs OSC Freq.
@
V
+
= 5V
DS009136-26
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LMC7660 | Switched Capacitor Voltage Converter |
| LMC8101 | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101BP | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101BPX | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101MM | Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMC7660IN/NOPB | 功能描述:電荷泵 Switched Cap Vltg Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| LMC7660IN/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Charge Pump Converter (DC-DC) IC |
| LMC7660MJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter |
| LMC8101 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown |
| LMC8101BP | 功能描述:IC OP AMP R-R I/O 8-USMD RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。