- 您現在的位置：買賣IC網 > PDF目錄361039 > LMH6559MFX (NATIONAL SEMICONDUCTOR CORP) High-Speed, Closed-Loop Buffer PDF資料下載
參數資料
| 型號： | LMH6559MFX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 緩沖放大器 |
| 英文描述： | High-Speed, Closed-Loop Buffer |
| 中文描述： | BUFFER AMPLIFIER, PDSO5 |
| 封裝： | SOT-23, 5 PIN |
| 文件頁數： | 19/22頁 |
| 文件大小： | 1078K |
| 代理商： | LMH6559MFX |
Application Notes
(Continued)
Discontinuities in a ground plane
A ground plane with traces routed over this plane results in
the build up of an electric field between the trace and the
ground plane as seen in
Figure 13
. This field is build up over
the entire routing of the trace. For the highest performance
the ground plane should not be interrupted because to do so
will cause the field lines to follow a roundabout path. In
Figure 17
it was necessary to interrupt the ground plane with
a crossing trace. This interruption causes the return current
to follow a longer route than the signal path follows to
overcome the discontinuity.
If needed it is possible to bypass the interruption with traces
that are parallel to the signal trace in order to reduce the
negative effects of the discontinuity in the ground plane. In
doing so, the current in the ground plane closely follows the
signal trace on the return path as can be seen in
Figure 18
.
Care must be taken not to place too many traces in the
ground plane or the ground plane effectively vanishes such
that even bypasses are unsuccessful in reducing negative
effects.
If the overall density becomes too high it is better to make a
design which contains additional metal layers such that the
ground planes actually function as ground planes. The costs
for such a pcb are increased but the payoff is in overall
effectiveness and ease of design.
Ground planes at top and bottom layer of a pcb
In addition to the bottom layer ground plane another useful
practice is to leave as much copper as possible at the top
layer. This is done to reduce the amount of copper to be
removed from the top layer in the chemical process. This
causes less pollution of the chemical baths allowing the
manufacturer to make more pcb’s with a certain amount of
chemicals. Connecting this upper copper to ground provides
additional shielding and signal performance is enhanced.
For lower frequencies this is specifically true. However, at
higher frequencies other effects become more and more
important such that unwanted coupling may result in a re-
duction in the bandwidth of a circuit. In the design of a test
circuit for the LMH6559 this effect was clearly noticeable and
the useful bandwidth was reduced from 1500MHz to around
850MHz.
As can be seen in
Figure 19
the presence of a copper field
close to the transmission line to and from the buffer causes
unwanted coupling effects which can be seen in the dip at
about 850MHz. This dip has a depth of about 5dB for the
case when all of the unused space is filled with copper. In
case of only one area being filled with copper this dip is
about 9dB.
Pcb board layout and component selection
Sound practice in the area of high frequency design requires
that both active and passive components be used for the
purposes for which they were designed. It is possible to
amplify signals at frequencies of several hundreds of MHz
using standard through hole resistors. Surface mount de-
vices, however, are better suited for this purpose. Surface
mount resistors and capacitors are smaller and therefore
parasitics are of lower value and therefore have less influ-
ence on the properties of the amplifier. Another important
issue is the pcb itself, which is no longer a simple carrier for
all the parts and a medium to interconnect them. The pcb
board becomes a real component itself and consequently
contributes its own high frequency properties to the overall
performance of the circuit. Sound practice dictates that a
20064159
FIGURE 17.
20064160
FIGURE 18.
20064161
FIGURE 19.
L
www.national.com
19
相關PDF資料 |
PDF描述 |
|---|---|
| LMH6559MA | High-Speed, Closed-Loop Buffer |
| LMH6559MAX | High-Speed, Closed-Loop Buffer |
| LMH6570MA | 2:1 High Speed Video Multiplexer |
| LMH6570MAX | 2:1 High Speed Video Multiplexer |
| LMH6570 | 2:1 High Speed Video Multiplexer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMH6559MFX/NOPB | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LMH6560 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Quad, High-Speed, Closed-Loop Buffer |
| LMH6560_04 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Quad, High-Speed, Closed-Loop Buffer |
| LMH6560MA | 制造商:Texas Instruments 功能描述:BUFFER QUAD 680MHZ CLOSED-LOOP SMD |
| LMH6560MA/NOPB | 功能描述:IC BUFF QUAD H/S C-LOOP 14-SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:LMH® 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。