- 您現在的位置：買賣IC網 > PDF目錄361044 > LMX9820ASM (NATIONAL SEMICONDUCTOR CORP) Bluetooth Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9820ASM |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Bluetooth Serial Port Module |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA116 |
| 封裝： | 10.10 X 14.10 MM, 2 MM HEIGHT, LGA-116 |
| 文件頁數： | 15/44頁 |
| 文件大小： | 579K |
| 代理商： | LMX9820ASM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Revision 1.0
15
www.national.com
L
7.0 Functional Description
(Continued)
7.2 MEMORY
The LMX9820A includes 256KB of programmable Flash
memory that can be used for code and constant data. It
allows single-cycle read access from the CPU. In addition
to storing all algorithms and firmware, the on-board Flash
also contains the IEEE 802 compliant Media Access Con-
troller (MAC) address (BDADDR). The firmware and the
BDADDR are programmed by National Semiconductor or
can be programmed by the customer either before assem-
bly into the host system or in-system. Module firmware can
also be updated during manufacturing or in-system using
the ISP capabilities of the LMX9820A. The LMX9820A
firmware uses the internal RAM for buffers and program
variables.
7.3 CONTROL AND TRANSPORT PORT
The LMX9820A provides one Universal Asynchronous
Receiver Transmitter (UART). It supports 8-bit data formats
with or without parity and one or two stop bits. The baud
rate is generated by hardware that is programmed at boot
time. Alternatively, the speed and configuration settings
can be read out of internal memory settings. The UART
can operate at baud rates of 2.4k, 4.8k, 7.2k, 9.6k, 19.2k,
38.4k, 57.6k, 115.2k, 230.4k, 460.8k and 921.6k. It imple-
ments flow control logic (RTS, CTS) to provide hardware
handshaking capability. The UART offers wakeup from the
low-power modes through the multi-input wakeup module.
UART logic thresholds are set via the IOVCC pin.
7.4 AUXILIARY PORTS
7.4.1 Reset_5100 and Reset_b#
Reset_5100 and Reset_b# are active low reset inputs for
the baseband controller and digital smart radio portions of
the LMX9820A, respectively. These pins are normally tied
together and are connected to the host system so that the
host can initialize the LMX9820A by asserting the reset
inputs. Upon de-assertion, the status of the module operat-
ing environment (Env) pads are sampled and the
LMX9820A enters the corresponding operational mode.
7.4.2 Operating Environment Pads (Env0 and Env1)
The module provides two operating environments (see
Table 17) selected by the states on the Env inputs sampled
at reset.
The ISP mode allows end-of-line or field programming of
the LMX9820A Flash memory by starting the baseband
controller from the boot block of memory.
7.4.3 Interface Select Inputs (ISEL1, ISEL2)
The interface selection pads are used for setting the UART
speed and settings. If ISEL1 and ISEL2 are unconnected,
they are pulled high by weak internal pullups, which select
a default baudrate of 921.6k baud. The settings for Stop-
bits, Startbit, and Parity are stored as internal non-volatile
storage (NVS) parameters. If a baud rate different from the
values listed in Table 18 is needed, ISEL 1 and ISEL2 must
be pulled low. This forces the device to read the UART
speed from the parameter table in NVS. The default baud
rate value programmed in NVS is 9.6k baud, however the
device firmware can be modified to support other values.
The default configuration in NVS is 1 Stopbit, 1 Startbit, and
No parity. Table 18 shows the ISEL1 and ISEL2 selection
settings.
7.4.4 Module and LInk Status Outputs
The LMX9820A provides signals that the host can use to
determine the real-time status of the radio link. The
TX_Switch_P signal (pad H3) is a real-time indication of
the current configuration (direction) of the transceiver. The
link status lines (Lstat_0 and Lstat_1, pads E8 and F8,
respectively) are GPIO lines controlled by the LMX9820A
firmware. The Host Wakeup line (Host_wu, pad F9) is
implemented using GPIO and firmware. It is used to bring
the host processor out of Sleep mode when link activity
calls for host processing. Host_wu can also be used by the
host to check if link activity is present. If Host_wu is active,
then link activity is present and the host loses network
awareness if the operating system continues to allow the
host processor to enter Sleep mode. Table 19 presents the
definitions of the various module and link status outputs.
Table 17. Operating Environments
Operating Environment
Env1
(Pad B11)
Env0
(Pad E9)
ISP Mode
1
0
Run (Normal) Mode (De-
fault)
1
1
Table 18. UART Speed Selection
ISEL2
(Pad H13)
Speed (baud)
1
1
0
ISEL1
(Pad J13)
1
0
1
Interface
UART
Settings
From NVS
From NVS
1Stop, 1Start,
No Parity
From NVS
921.6k
115.2k
9.6k
0
0
Check NVS
Table 19. Module/Link Status Definitions
L
(
L
(
T
(
H
(
Mode
x
1
x
x
At least 1 SPP link es-
tablished
No active SPP link
Transceiver = Transmit
Transceiver = Receive
Host can Sleep
Wakeup host/host
should not Sleep
x
x
x
x
x
0
x
x
x
x
x
1
0
x
x
x
x
x
0
1
相關PDF資料 |
PDF描述 |
|---|---|
| LMX9820 | Bluetooth Serial Port Module |
| LMX9820SB | Bluetooth Serial Port Module |
| LMX9820SBX | Bluetooth Serial Port Module |
| LP3882ESX-1.2 | 1.5A Fast-Response Ultra Low Dropout Linear |
| LP3882ESX-1.5 | 1.5A Fast-Response Ultra Low Dropout Linear |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9820ASM/NOPB | 制造商:Texas Instruments 功能描述:IC MODULE BLUETOOTH 116-LTCC |
| LMX9820ASMX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth Serial Port Module |
| LMX9820ASMX/NOPB | 制造商:Texas Instruments 功能描述:Bluetooth Class II 3.3V 0.704Mbps 116-Pin LTCC T/R 制造商:Texas Instruments 功能描述:MODULE BLUETOOTH SERIAL PORT SMD |
| LMX9820SB | 制造商:Texas Instruments 功能描述: 制造商:Texas Instruments 功能描述:MODULE BLUE TOOTH 116-LTCC 制造商:Texas Instruments 功能描述:BLUETOOTH MODULE 2.4GHZ 704KBPS |
| LMX9820SBX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth Serial Port Module |
發布緊急采購，3分鐘左右您將得到回復。