- 您現在的位置：買賣IC網 > Datasheet目錄41 > LT3570IFE#TRPBF (Linear Technology)IC REG BUCK/BST/LINEAR 20TSSOP Datasheet資料下載
參數資料
| 型號： | LT3570IFE#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 7/20頁 |
| 文件大小： | 288K |
| 描述： | IC REG BUCK/BST/LINEAR 20TSSOP |
| 標準包裝： | 2,500 |
| 拓撲： | 降壓（降壓）（1），升壓（升壓）（1），線性（LDO）（1） |
| 功能： | 車載 |
| 輸出數： | 3 |
| 頻率 - 開關： | 500kHz ~ 2.1MHz |
| 電壓/電流 - 輸出 1： | 可調至0.8V，1.5A |
| 電壓/電流 - 輸出 2： | 可調至0.8V，1.5A |
| 電壓/電流 - 輸出 3： | 控制器 |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 2.5 V ~ 36 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 20-TSSOP-EP |
| 包裝： | 帶卷 (TR) |
LT3570
7
3570fb
PIN FUNCTIONS (QFN/TSSOP)
V
IN2
(Pins 1,2/Pin 14): Input Voltage for the Buck Regulator.
This pin also supplies the current to the internal circuitry
of the LT3570. This pin must be locally bypassed with a
capacitor.
SW2 (Pin 3/Pin15): Switch Node. This pin connects to
the emitter of an internal NPN power switch. Connect a
diode, inductor and boost capacitor to this pin to form
the buck regulator.
SW1 (Pin 4/Pin16): Switch Node. This pin connects to the
collector of an internal NPN power switch. Connect a diode
and inductor to this pin to form the boost regulator.
GND (Pins 5, 6, 16, 25/Pins 17, 21): Ground. The Exposed
Pad of the package provides both electrical contact to
ground and good thermal contact to the printed circuit
board. The Exposed Pad must be soldered to the circuit
board for proper operation.
V
IN1
(Pin 7/Pin18): Input Voltage for the Boost Regulator.
This pin supplies current to drive the boost NPN transistor
of the LT3570. This pin must be locally bypassed with a
capacitor.
SS1 (Pin 8/Pin 19): Soft-Start Pin. Place a soft-start
capacitor here. Upon start-up, a current charges the
capacitor to 2V. This pin ramps the reference voltage of
the boost switcher.
V
C1
(Pin 9/Pin 20): Control Voltage and Compensation Pin
for the Internal Error Ampli er. Connect a series RC from
this pin to ground to compensate the switching regulator
loop for the boost regulator.
FB1 (Pin 10/Pin 1): Feedback Pin. The LT3570 regulates
this pin to 788mV. Connect the feedback resistors to
this pin to set the output voltage for the boost switching
regulator.
SHDN1 (Pin 11/Pin 2): Shutdown Pin. Tie to 1.4V or more
to enable the boost switcher. Tie all SHDN pins to 0.3V or
less to shutdown the part.
SHDN2 (Pin 12/Pin 3): Shutdown Pin. Tie to 1.4V or more
to enable the buck switcher. Tie all SHDN pins to 0.3V or
less to shutdown the part.
SHDN3 (Pin13/Pin 4): Shutdown Pin. Tie to 1.5V or more
to enable the NPN LDO. Tie all SHDN pins to 0.3V or less
to shutdown the part.
SYNC (Pin 14/Pin 5): Synchronization Pin. The SYNC pin
is used to synchronize the internal oscillator to an exter-
nal signal. The synchronizing range is equal to the initial
operating frequency set by the R
T
pin up to 1.3 times the
initial operating frequency.
R
T
(Pin 15/Pin 6): Frequency Set Pin. Place a resistor to
GND to set the internal frequency. The range of oscillation
is 500kHz to 2MHz.
SS2 (Pin 17/Pin 7): Soft-Start Pin. Place a soft-start
capacitor here. Upon start-up, a current charges the
capacitor to 2V. This pin ramps the reference voltage of
the buck switcher.
V
C2
(Pin 18/Pin 8): Control Voltage and Compensation Pin
for the Internal Error Ampli er. Connect a series RC from
this pin to ground to compensate the switching regulator
loop for the buck regulator.
FB2 (Pin 19/Pin 9): Feedback Pin. The LT3570 regulates
this pin to 788mV. Connect the feedback resistors to
this pin to set the output voltage for the buck switching
regulator.
FB3 (Pin 20/Pin 10): Feedback Pin. The LT3570 regulates
this pin to 788mV. Connect the feedback resistors to this
pin to set the output voltage for the LDO controller.
NPN_DRIVE (Pin 21/Pin 11): Base Drive for the External
NPN. This pin provides a bias current to drive the base of
the NPN. This base current is driven from the IN3 supply
voltage.
V
IN3
(Pin 22/Pin 12): Input Voltage for the NPN LDO. This
pin supplies current to drive the base of the NPN. This pin
must be locally bypassed with a capacitor.
BIAS (Pin 23): QFN Package Only. This pin supplies current
to the internal circuitry of the LT3570 if greater than 2.5V.
This pin must be locally bypassed with a capacitor.
BOOST (Pin 24/Pin 13): Bias for the Base Drive of the
NPN Switch for the Buck Regulator. This pin provides a
bias voltage higher than V
IN2
. The voltage on this pin is
charged up through an external Schottky diode.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3645HMSE#TRPBF | IC REG DL BUCK/LINEAR 12-MSOP |
| LT3694IFE-1#TRPBF | IC REG TRPL BUCK/LINEAR 20TSSOP |
| LT4220IGN#TR | IC CTLR HOTSWAP DUAL 16-SSOP |
| LT4250LCN8 | IC CONTRLR HOT SWAP NEG 48V 8DIP |
| LT4254CGN | IC CTRLR HOTSWAP POSVOLT 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3570IUF#PBF | 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3570IUF#TRPBF | 功能描述:IC REG TRPL BCK/BST/LINEAR 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| LT3570IUF-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
| LT3570IUF-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A Buck Converter, 1.5A Boost Converter and LDO Controller |
| LT3571EUD#PBF | 功能描述:IC REG BOOST ADJ 0.47A 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
發布緊急采購，3分鐘左右您將得到回復。