- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4212IMS#TRPBF (Linear Technology)IC CTRLR HOTSWAP TIMEOUT 10MSOP Datasheet資料下載
參數資料
| 型號： | LTC4212IMS#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 8/24頁 |
| 文件大小： | 234K |
| 描述： | IC CTRLR HOTSWAP TIMEOUT 10MSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.5 V ~ 16.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
8
LTC4212
4212f
U
PI FU CTIO S
ON (Pin 1): On/Off Control Input. The ON pin is used to
enable and disable LTC4212 operation and reset internal
logic and the electronic circuit breaker (ECB). It must be
pulled high (>1.316V) to start the first system timing
cycle. If the ON pin is pulled low (<0.455V typical) for more
than 10祍, the internal logic is reset and the GATE pin is
pulled down by a 200礎 current to turn off the external
FET. If the ON pin is pulled low for more than 120祍, the
electronic circuit breaker is reset. This pin is tied to a
resistive divider in latch-off applications or to the FAULT
pin and an external RC circuit in auto-retry applications.
TIMER (Pin 2): System Timer Input. An external capacitor
(C
TIMER
) connected from this pin to ground determines
the duration of the first and second system timing cycles.
The first timing cycle allows time for the board to be
inserted properly. During the second timing cycle, a
soft-start circuit controls the gate of the external
N-channel FET to limit inrush currents from the backplane
supply.
PGT (Pin 3): Power Good Timer Input. An external capaci-
tor (C
PGT
) connected from this pin to ground sets the
power good time-out period. This is the maximum time
allowed for externally monitored DC/DC converters to
power-up into regulation and pull the PGI pin high. The
nominal time-out cycle is 1.81s/礔 and begins from the
end of the second system timing cycle. This pin is pulled
to ground by an internal switch when the power good timer
is disabled or when the ECB is tripped.
PGF (Pin 4): Power Good Glitch Filter Input. An external
capacitor (C
PGF
) connected from this pin to ground deter-
mines the power good glitch filter delay. The glitch filter is
enabled if the externally monitored DC/DC converters are
powered up within the power good time-out period (see
Pin 3). If the PGI pin goes low for longer than the filter
delay, the ECB is tripped.
GND (Pin 5): Device Ground Connection. Connect this pin
to the systems analog ground plane.
PGI (Pin 6): Power Good Input Pin. This pin is used by the
power good circuit to sense the open drain RST output or
comparator outputs of an external supply monitor IC or
the PGOOD output of a DC/DC converter. It requires an
external pull-up resistor to a voltage above the V
FAULT
threshold 1.236V. When the power good timer times out
(see Pin 3), PGI must be high to avoid tripping the ECB and
to enable the power good glitch filter.
GATE (Pin 7): Gate Output Pin. The output signal at this
pin is the high side gate drive for the external N-channel
FET pass transistor.
As shown in the Block Diagram, an internal charge pump
supplies a 10礎 gate current and sufficient gate voltage to
drive the external FET for supply voltages from 2.5V to
16.5V. The internal charge pump and zener clamps at the
charge pump output determine the gate drive voltage
(V
GATE
= V
GATE
V
CC
). The charge pump produces a
minimum 4V of V
GATE
for supplies in the range of 2.5V <
V
CC
< 4.75V. For V
CC
> 4.75V, the V
GATE
is limited by
zener clamp Z1 connected between the charge pump
output and the V
CC
pin. The V
GATE
is typically at 12V and
with guaranteed minimum value of 10V. For V
CC
> 15V, the
zener clamp Z2 sets the limitation for V
GATE
. Z2 clamps
the gate voltage to ground to 28V typically. The minimum
Z2s clamp voltage is 23V. This effectively sets V
GATE
to
8V minimum.
SENSE (Pin 8): Circuit Breaker Set Pin. With a sense
resistor placed in the power path between V
CC
and SENSE,
the LTC4212s electronic circuit breaker trips if the voltage
across the sense resistor exceeds the thresholds set
internally for the SLOW COMP and the FAST COMP, as
shown in the Block Diagram. The threshold for the SLOW
COMP is V
CB(SLOW)
= 50mV, and the electronic circuit
breaker trips if the voltage across the sense resistor
exceeds 50mV for 18祍.
Under transient conditions where large step current
changes can and do occur over shorter periods of time, a
second (fast) comparator instead trips the electronic
circuit breaker. The threshold for the FAST COMP is set at
V
CB(FAST)
= 150mV, and the circuit breaker trips if the
voltage across the sense resistor exceeds 150mV for more
than 500ns. To disable the electronic circuit breaker,
connect the V
CC
and SENSE pins together.
V
CC
(Pin 9): This is the positive supply input to the LTC4212. The
LTC4212 operates from 2.5V < V
CC
< 16.5V, and the supply
current is typically 1mA. An internal undervoltage lockout circuit
disables the device until the voltage at V
CC
exceeds 2.34V.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4214-1IMS#TRPBF | IC CTRLR HOTSWAP NEGVOLT 10MSOP |
| LTC4215IUFD#PBF | IC CNTRLR HOT SWAP 24-QFN |
| LTC4216IDE#TRPBF | IC CNTRLR HOT SWAP 12-DFN |
| LTC4221IGN#TRPBF | IC CTRLR HOTSWAP DUAL 16SSOP |
| LTC4222CG#PBF | IC CTRLR DUAL HOT SWAP 36-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4213 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:No RSENSE? Electronic Circuit Breaker |
| LTC4213CDDB | 制造商:LINER 制造商全稱:Linear Technology 功能描述:No RSENSE? Electronic Circuit Breaker |
| LTC4213CDDB#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 6V 8-Pin DFN EP 制造商:Linear Technology 功能描述:HOT SWAP CNTRL 6V INT SW 8DFN 制造商:Linear Technology 功能描述:HOT SWAP CNTRL, 6V, INT SW, 8DFN |
| LTC4213CDDB#TRMPBF | 功能描述:IC CIRC BREAK ELEC 8-DFN RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| LTC4213CDDB#TRPBF | 功能描述:IC CIRC BREAK ELEC 8-DFN RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
發布緊急采購，3分鐘左右您將得到回復。